Hooker headers suck!
Thread Starter
TECH Addict
Joined: Dec 2001
Posts: 2,337
Likes: 0
From: Auburn, AL
Hooker headers suck! This is a warning to all hoping to save money and get Hooker headers. This is what I did and I hate mine. It is damn near impossible to get the passenger side 02 in with the fuel line and heat shield there. They rust bad, even with Jet-Hot coating (this is not Hookers fault, though). They have shitty primary welds, and I can't get anything to seal well to their collectors. Save your money for decent headers, like QTPs or Kooks.
Re: Hooker headers suck! I have never had a problem with mine either...Install was good, with no clearance issues...I think they are the best bang for the buck and they perform really well...Just my .02...
Kevin
Kevin
TECH Fanatic
Joined: Feb 2002
Posts: 1,782
Likes: 0
From: Friendswood TX
Re: Hooker headers suck! No hes talking about when it goes underneath. Like near the break line and all that fun stuff. The heat sheild is in the way, kinda. I just bent it and called it a day. see the pic its on the right.
I didnt have any probelms either. They are a lot better than macs
I didnt have any probelms either. They are a lot better than macs
Re: Hooker headers suck! My brother and I installed my Hookers today in about 4 1/2 hours. Was the first time for either of us to install headers on an LS1 (my silver 2002 Camaro Z28) and had no problems.
Hey Z-Rated, nice Silver 02 Z28.
Thought that undercarriage pic looked somewhat familiar after today.
---Sebastian Lopez Jr.
www.LopezRacing.com
Hey Z-Rated, nice Silver 02 Z28.
Thought that undercarriage pic looked somewhat familiar after today.---Sebastian Lopez Jr.
www.LopezRacing.com
TECH Junkie
Joined: Dec 2001
Posts: 3,242
Likes: 0
From: Lakeland, FL
Re: Hooker headers suck! I like mine as well, I took some tin snips and cut a little triangle to get the o2 sensor to fit better. From my experience nothing ever fits perfect but these are not to bad.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo Thread Starter
TECH Addict
Joined: Dec 2001
Posts: 2,337
Likes: 0
From: Auburn, AL
Re: Hooker headers suck! I've had mine for a long time, they perform well for the money, but I wouldn't buy them again.
BTW, I did mean driver side 02, not passenger side like I put. I've bent the heat shielding all kinds of ways, and it's still a bitch to get it in.
BTW, I did mean driver side 02, not passenger side like I put. I've bent the heat shielding all kinds of ways, and it's still a bitch to get it in.
Re: Hooker headers suck! What heat sheilding....... I took the **** out. With Jet-hots you dont have that problem because the o2 bungs are on the other side so i guess they did take a design and make it a little better.
TECH Resident
iTrader: (3)
Joined: Nov 2001
Posts: 979
Likes: 0
From: Richmond, VA Where fast cars, well......are hard to come by.
Re: Hooker headers suck! I'm happy with my set. Although I am fairly dissappointed in their choice of clamps for the system. Anyone getting these should go to napa and get 3 of the stainless steel band clamps (they say easy seal on the top). Those suckers work awesome. The supplied clamps managed to put some nice dents in my ypipe and didn't seal for crap.
Re: Hooker headers suck! I was happy with mine when I had them. Sold them to a buddy and his driver's side O2 was pretty tight like yours. They seem to be louder and raspier then other headers I think too.
Re: Hooker headers suck! My set of Hookers had the following issues:
1/4 inch gap that wasn't welded, that would have caused a bad exhaust leak.
Primaries were full of slag
O2 sensor couldn't be screwed into the hole because Hooker managed to misalign the O2 by about 1/4 of an inch.
Flanges weren't flat had to filed.
Collectors not oriented the same as other Hookers to the Y pipe has to be cut apart and welded back together to get it to work with the Hookers.
And the O2 sensor issue as mentioned above.
Hookers are a crap shoot. Their quailty control is lame. I'd not buy them again. Might give the Jet Hot's a shot or the PPC's or other quailty header would be on my list.
1/4 inch gap that wasn't welded, that would have caused a bad exhaust leak.
Primaries were full of slag
O2 sensor couldn't be screwed into the hole because Hooker managed to misalign the O2 by about 1/4 of an inch.
Flanges weren't flat had to filed.
Collectors not oriented the same as other Hookers to the Y pipe has to be cut apart and welded back together to get it to work with the Hookers.
And the O2 sensor issue as mentioned above.
Hookers are a crap shoot. Their quailty control is lame. I'd not buy them again. Might give the Jet Hot's a shot or the PPC's or other quailty header would be on my list.
Re: Hooker headers suck! i love mine, they went in great and look bad ***. but i do agree to a point on the 02 bung on the drivers side it was right against the fuel lines
Re: Hooker headers suck! Mine have been on the car since the 30 mile mark, I've got 20,000 on them in a little over a year. Done a couple of head swaps where I had to take them out and put them back in... through all of it, I don't have one complaint about them.
