Ls6 Head Limitation's
#1
TECH Apprentice
Thread Starter
iTrader: (16)
Join Date: May 2009
Location: MS
Posts: 324
Likes: 0
Received 0 Likes
on
0 Posts
Ls6 Head Limitation's
Are Stock ls6 heads limited on performance? I'm wondering can i go in the 10's with this stock head's and aftermarket cam. Im going to run 3.73 gears, 125 wet shot, and LT headers ,ory and Lid. With a good tune. What cam works great with these heads I want to make good hp on motor but really go in the numbers with nitrous. If I can run 10.90's or better im good. O yea I will be running a 3600 stall.
__________________
__________________
#4
Staging Lane
Join Date: Jun 2009
Location: coon rapids mn
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
good springs and a valve job +a good nos tune will do it .950 psi bottle pressure +enough fuel pressure and pull out 6* timing, and short shift 500rpm below peak na hp .
#5
TECH Enthusiast
iTrader: (3)
Join Date: Dec 2004
Location: Tulsa OK
Posts: 514
Likes: 0
Received 0 Likes
on
0 Posts
Yeah don't listen to suzookiegsxr. You can use other cams besides the LS6 cam with those heads and have great results. You should look into the MS3 cam for good numbers all motor that really wakes up with the juice.
Trending Topics
#11
TECH Fanatic
iTrader: (35)
Join Date: Aug 2004
Location: Paramount CA
Posts: 1,016
Likes: 0
Received 0 Likes
on
0 Posts
people have gone bottom 10's regularly and high 9s ocassionally on stock unported LS1 heads and nitrous.
LS6 castings have major potential to be worked over later on. TEA has gotten 320cfm from LS6 castings
LS6 castings have major potential to be worked over later on. TEA has gotten 320cfm from LS6 castings
#17
TECH Fanatic
iTrader: (1)
You leave your car in 3 depending on how many clutch packs you have. I am running an RPM Stage II 4L60E/PCT 3400 stall set up and I have 2 extra clutch packs for 3rd specifically for 1/4 runs if not then you want to put her on drive. Whats the tranny matted to your 3600 stall?
#19
TECH Junkie
iTrader: (13)
Join Date: Sep 2004
Location: Fort Myers, FL.
Posts: 3,857
Likes: 0
Received 0 Likes
on
0 Posts
there are guys running ls6 heads on 408ci engines so I think you will be fine. Especially if you get them worked over.
If you get a cam make sure you get- valvesprings, pushrods, oil pump, timing chain. good idea to change out fuel filter, and put in new spark plugs escpecially if you are going to spray. Tr6's would a good choice.
How is your fuel system- a racetronics kit and injectors is almost the minimum you need.
10 bolt or aftermarket rear- if stock start saving for a new one.
tranny- you said stock- it will break with the power you are thinking so start saving for a new one
Stock suspension- it is going to be hard to get the power to the ground.
Good luck
If you get a cam make sure you get- valvesprings, pushrods, oil pump, timing chain. good idea to change out fuel filter, and put in new spark plugs escpecially if you are going to spray. Tr6's would a good choice.
How is your fuel system- a racetronics kit and injectors is almost the minimum you need.
10 bolt or aftermarket rear- if stock start saving for a new one.
tranny- you said stock- it will break with the power you are thinking so start saving for a new one
Stock suspension- it is going to be hard to get the power to the ground.
Good luck