compression and head?
compression and head? Before i get flamed, I have spent the last 2 days searching for an answer and have come up short.
I have a lq4 stock short block. I am thinking about putting a set of stock 706 heads with gm mls 6.0 gaskets on it(i have them laying around). By my figuring the compression will come out somewhere around 10.5 to 1. Does that look right to yall. Is there any reason why I could not use these heads?
The engine will be going in a s10 that is being built for a sport truck NOT a race truck. I do know that the heads are not the best choice. It is going to be more bark then bite.
Thanks for the help
I have a lq4 stock short block. I am thinking about putting a set of stock 706 heads with gm mls 6.0 gaskets on it(i have them laying around). By my figuring the compression will come out somewhere around 10.5 to 1. Does that look right to yall. Is there any reason why I could not use these heads?
The engine will be going in a s10 that is being built for a sport truck NOT a race truck. I do know that the heads are not the best choice. It is going to be more bark then bite.
Thanks for the help
Without all of the specifics, and a few guesses...
Cylinder Head Volume (cc):-------61.150
Piston Head Volume (cc):----------0.000
Gasket Thickness (in.):-----------0.051
Gasket Bore (in.):----------------4.010(?)
Cylinder Bore Diameter (in.):-----4.000
Deck Clearance (in.):----------(-)0.005(?)
Stroke (in.):---------------------3.622
STATIC COMPRESSION RATIO:--------11.558
Cylinder Head Volume (cc):-------61.150
Piston Head Volume (cc):----------0.000
Gasket Thickness (in.):-----------0.051
Gasket Bore (in.):----------------4.010(?)
Cylinder Bore Diameter (in.):-----4.000
Deck Clearance (in.):----------(-)0.005(?)
Stroke (in.):---------------------3.622
STATIC COMPRESSION RATIO:--------11.558
It does, I didn't. I had them backwards. With a dished piston, 6.7cc's, results are below.
https://ls1tech.com/forums/conversio...y-not-lq4.html
https://ls1tech.com/forums/conversio...y-not-lq4.html
Without all of the specifics, and a few guesses...
Cylinder Head Volume (cc):-------61.150
Piston Head Volume (cc):----------6.700
Gasket Thickness (in.):-----------0.051
Gasket Bore (in.):----------------4.010(?)
Cylinder Bore Diameter (in.):-----4.000
Deck Clearance (in.):----------(-)0.005(?)
Stroke (in.):---------------------3.622
STATIC COMPRESSION RATIO:--------10.643
Cylinder Head Volume (cc):-------61.150
Piston Head Volume (cc):----------6.700
Gasket Thickness (in.):-----------0.051
Gasket Bore (in.):----------------4.010(?)
Cylinder Bore Diameter (in.):-----4.000
Deck Clearance (in.):----------(-)0.005(?)
Stroke (in.):---------------------3.622
STATIC COMPRESSION RATIO:--------10.643
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
