1nasty86

iTrader: (63)

ive been on the edge on what head to buy for my ls2 and i finally took the leap, decided to go with the trickflow 225. car previously made 463/434 with a set of ported/shaved 317's, 230/238 eps cam, fast 102. im starting to pull the heads off and then i wait for my new heads.



intake ready to be sent for port matching


ill be pulling the 317's in the morning.

RENE'S RAGE

iTrader: (96)

Good choice!

Rise of the Phoenix

iTrader: (27)

You'll be very happy with that choice. Can't really go wrong with TFS heads. Are you going to shave/paint the intake?

1nasty86

iTrader: (63)

No, just port match it.

1nasty86

iTrader: (63)

looks like i was alittle over on duration on my intake lobe.. i can barely catch it with my finger nail so ill just run it, no sharp edges to cause bad heat spots. Anyway.. the heads are off and i await the arrival of my trickflows.

3rdCoastPowerSports

iTrader: (5)

just a kiss... did you measure the PTV clearance on your old setup?

1nasty86

iTrader: (63)

no i did not.. i had a reputable cam specialist spec me this camshaft so i figured i was fine. No harm done tho, heads are fine as with everything else.

Joshua8336

don't u ever get tired of posting the same thing over and over again. this exact thread is on TGO

1nasty86

iTrader: (63)

And? I was asked to post it up on tgo.

Joshua8336

just figured u'd get tired of reposting everything, almost every thread u have on here, is on TGO

1nasty86

iTrader: (63)

so then since i post in the ltx/lsx forum on tgo and i post on ls1tech then i guess TPI Terror, Outlaw drifter/STREETDEMON, BlueZee28, Mw66nova, RPD Vette84/INTIMIDATOR Z, Xpndbl3 and Grifter all should be banned from all forums since we ALL post most of our stuff on both... shame on us.

'02 StripedSS

iTrader: (14)

Great choice in heads, you can't go wrong with TFS!!!

3rdCoastPowerSports

iTrader: (5)

post some pics of the heads when you get them

1nasty86

iTrader: (63)

oh you can bet i will, they cost'd me an arm and my first born. i ordered the heads from a member on here and he will be purchasing them from trickflow and milling them to my spec's and port matching my intake, so it will be a week or two before i actually get my hands on them.

TPI TERROR

iTrader: (52)

Lol just saw the reply. Not everyone is on Tgo any more . This site is highly convenient/ very recommended and far more advanced

Back to topic those heads should be a nice improvement.

MikeyZ

iTrader: (20)

the guys on Tgo are hardcore on tpi because thats how they make there money if people switch to ls then the lose buisness... they dont want to learn the new stuff

NemeSS

iTrader: (127)

jt76

iTrader: (10)

errybody mad

Can never go wrong with a TFS product

1nasty86

iTrader: (63)

But back to the heads, I hope to make over 500hp or atleast be close. but going from 463 to 500 seems alot. The 463 was without an u/d pulley so just say going from 471 to 500 is 29rwhp...

BrianSF-GA

This will be an interesting outcome ... I am wanting to see the rwt change with the FAST 102. Most of the installs I have read about had not had significant torque increases. I would like to go to a larger head, but my TFS CNC 215's flow 266.1/321.8 cfm's at 0.600 ... that's pretty good for a 215 and thought about a FAST 102. I hate to lose my torque!

Are you running a stock cube 6.0?