What intake is this?? Pics inside
#21
TECH Veteran
Thread Starter
iTrader: (33)
Join Date: Nov 2001
Location: Port Richey
Posts: 4,266
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 99 TA
I thought that there was a guy with a vette on here a year or 2 ago that went to Katech and they built a C5R motor with a custom intake for him. Block, heads everything. It didn’t dyno real high because it was a mild setup and everyone gave him **** for it like why go C5R if it isn’t all out and the cost was crazy. Well the pictures of the motor had an intake that looked like the LS6 intake however the runners were not rounded but fatter like the ones in the intake pictured here. By the look of the ports I would also say that it would fit C5R heads. From what I remember I thought the guy wanted a motor that looked and almost sounded stock but had nice power.
Possible...however...if you look at the TB mount at the inlet...it has a 4 bolt pattern. The LS2 90 mm TB will bolt directly to this intake in the pics. I doubt they had that info back then.
#22
TECH Enthusiast
Join Date: Feb 2004
Location: Foley, Alabama-southern Alabama
Posts: 743
Likes: 0
Received 0 Likes
on
0 Posts
I agree with WILWAXU,looks like CR-5 STUFF TO ME wide and not as tall of ports as ls-1 heads .I seen somebody stated that the 2006??Corvette will have a 427 motor, also read GM is thinking of putting it in the GTO too!GM may put the GEN-3 motors in some other cars such as Grand Prix and similar chassis, I hope GM comes out with something that deserves such a capable engine,I saw a GTO at the dealer the other day could not look more RICIER to me !!
#23
TECH Apprentice
iTrader: (1)
Join Date: Nov 2001
Location: Ohio
Posts: 303
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 383LQ4SS
Possible...however...if you look at the TB mount at the inlet...it has a 4 bolt pattern. The LS2 90 mm TB will bolt directly to this intake in the pics. I doubt they had that info back then.
#25
On The Tree
iTrader: (2)
Join Date: Sep 2002
Location: Knoxville, TN
Posts: 181
Likes: 0
Received 0 Likes
on
0 Posts
I can only hope GM is doing good things. I've owned a lot of cars and a awhile ago I realized ALL of them were GM. These are cars I wanted, I didn't care abouts brands or whatnot.
BTW Did anyone else notice the truck intake in chevy hi-performance (lame I know) that made more top end HP than the LSX?
It looks like a tunnel ram style intake and is supposedly is 4 inches installed height higher than the LS6/LS1 intake.
BTW Did anyone else notice the truck intake in chevy hi-performance (lame I know) that made more top end HP than the LSX?
It looks like a tunnel ram style intake and is supposedly is 4 inches installed height higher than the LS6/LS1 intake.
#26
Under criminal investigation for fraud
iTrader: (-2)
Join Date: Jan 2004
Posts: 1,350
Likes: 0
Received 0 Likes
on
0 Posts
That intake is a LS7, for the big cubic inch corvette that will be coming out in a few years. Nice manifold and makes good power. When I worked at Katech we were doing the initial tests on that manifold. If you think the manifold is nice wait till you guy's see the heads it bolts on to. They are going to be a cross between the current heads and the C5R heads. I have flowed a few sets and they have all flowed right around 370cfm. Can't wait till they come out!!
#27
10 Second Club
iTrader: (15)
Join Date: Nov 2001
Location: St. Michael, MN.
Posts: 4,519
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Chris@AP-Engineering
That intake is a LS7, for the big cubic inch corvette that will be coming out in a few years. Nice manifold and makes good power. When I worked at Katech we were doing the initial tests on that manifold. If you think the manifold is nice wait till you guy's see the heads it bolts on to. They are going to be a cross between the current heads and the C5R heads. I have flowed a few sets and they have all flowed right around 370cfm. Can't wait till they come out!!
#28
TECH Regular
iTrader: (2)
Join Date: Oct 2003
Location: REDFORD,MI
Posts: 438
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Chris@AP-Engineering
That intake is a LS7, for the big cubic inch corvette that will be coming out in a few years. Nice manifold and makes good power. When I worked at Katech we were doing the initial tests on that manifold. If you think the manifold is nice wait till you guy's see the heads it bolts on to. They are going to be a cross between the current heads and the C5R heads. I have flowed a few sets and they have all flowed right around 370cfm. Can't wait till they come out!!
any ideas on runner volume???
and/or why gm seems to be going back to "rectangle" style ports???
#29
12 Second Club
iTrader: (1)
Join Date: Apr 2004
Location: Clarksville, TN
Posts: 1,369
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Chris@AP-Engineering
That intake is a LS7, for the big cubic inch corvette that will be coming out in a few years. Nice manifold and makes good power. When I worked at Katech we were doing the initial tests on that manifold. If you think the manifold is nice wait till you guy's see the heads it bolts on to. They are going to be a cross between the current heads and the C5R heads. I have flowed a few sets and they have all flowed right around 370cfm. Can't wait till they come out!!
#30
Originally Posted by CamTom12
ok, I have a question then... (probably a stupid one, too ) In the LS series engines, would the heads be interchangable? When they come out could I bolt a set onto my LS1?
#32
TECH Fanatic
Join Date: Apr 2003
Location: Albuquerque, NM
Posts: 1,109
Likes: 0
Received 0 Likes
on
0 Posts
I like the two piece design, like the FAST LSX. Makes port matching possible!
Dang, the HP wars are hitting a very high note! Can't wait to see what comes next...
Dang, the HP wars are hitting a very high note! Can't wait to see what comes next...
#33
Launching!
Join Date: Mar 2004
Location: Ontario Canada
Posts: 222
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Chris@AP-Engineering
That intake is a LS7, for the big cubic inch corvette that will be coming out in a few years. Nice manifold and makes good power. When I worked at Katech we were doing the initial tests on that manifold. If you think the manifold is nice wait till you guy's see the heads it bolts on to. They are going to be a cross between the current heads and the C5R heads. I have flowed a few sets and they have all flowed right around 370cfm. Can't wait till they come out!!
I've been wanting to get a stroker built for my SS but I'm assuming that all this LS7 stuff may be worth the wait.
A production 427 should be much cheaper than a C5R block or even a Darton resleeve. Now I'm hoping it will fit in the Camaro and headers wont be a problem.
#34
10 Second Club
Originally Posted by CamaroJoe
Is this it by any chance?
I've been wanting to get a stroker built for my SS but I'm assuming that all this LS7 stuff may be worth the wait.
A production 427 should be much cheaper than a C5R block or even a Darton resleeve. Now I'm hoping it will fit in the Camaro and headers wont be a problem.
I've been wanting to get a stroker built for my SS but I'm assuming that all this LS7 stuff may be worth the wait.
A production 427 should be much cheaper than a C5R block or even a Darton resleeve. Now I'm hoping it will fit in the Camaro and headers wont be a problem.
#35
On The Tree
Join Date: Nov 2001
Location: Haughton, LA
Posts: 169
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Chris@AP-Engineering
That intake is a LS7, for the big cubic inch corvette that will be coming out in a few years. Nice manifold and makes good power. When I worked at Katech we were doing the initial tests on that manifold. If you think the manifold is nice wait till you guy's see the heads it bolts on to. They are going to be a cross between the current heads and the C5R heads. I have flowed a few sets and they have all flowed right around 370cfm. Can't wait till they come out!!
Did the heads use a traditional 2 valve design, or did they have 3 valves like much of the speculation suggests?
#39
hello charlie...
dont you hate bad karma?
i felt maybe all your buddies here should be reminded of your past adventures!
- Salutes from LastMVP
http://www.pirate4x4.com/forum/showthread.php?t=399203
dont you hate bad karma?
i felt maybe all your buddies here should be reminded of your past adventures!
- Salutes from LastMVP
http://www.pirate4x4.com/forum/showthread.php?t=399203