230/234 591/598 on a 114
#25
TECH Resident
Thread Starter
iTrader: (1)
Join Date: Apr 2003
Location: Tampa, FL
Posts: 798
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
haha ok, Im putting cam in tomorrow. What should I do to check p to v clearance. I was going to do the turn over test and see if anything hits, but now Im worried I'm reading about it could push down a little further "Valve float" and break my piston???
#26
TECH Enthusiast
iTrader: (10)
Join Date: Dec 2003
Location: Central Kentucky
Posts: 649
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Michael Ozorowsky
haha ok, Im putting cam in tomorrow. What should I do to check p to v clearance. I was going to do the turn over test and see if anything hits, but now Im worried I'm reading about it could push down a little further "Valve float" and break my piston???
#32
TECH Regular
iTrader: (5)
Join Date: Sep 2002
Location: Phoenix, AZ
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Michael Ozorowsky
Cam has no advance ground into it.
#33
TECH Regular
iTrader: (5)
Join Date: Sep 2002
Location: Phoenix, AZ
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Cal
Naw, if it has a couple degrees of advance, it should peak at about 6600 rpm.
Ok, so if you peak @ 6600 you're also going to shift there? I know I wouldn't be shifting @ exactly where my car makes peak power.......
#35
TECH Regular
iTrader: (5)
Join Date: Sep 2002
Location: Phoenix, AZ
Posts: 487
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Michael Ozorowsky
soi you guys think this will have no power down low???
The cam I had was a PIG until about 3200 rpms....Yours will be sluggish until a bit higher in the rpm range.
#37
TECH Resident
Thread Starter
iTrader: (1)
Join Date: Apr 2003
Location: Tampa, FL
Posts: 798
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
what kind of #'s you think I'll put down. Install is done. Waiting to fix a coolant leak (Gotta replace gasket) and then all should be good. I can't WAIT. Start tuning tomorrow or next day I hope.
#40
LS1Tech Sponsor
iTrader: (12)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
That Cam was made for the Blower you were suppose to be buying with it.It is not optimal for a NA car as it peaks way up in the power range.The idle is lopey and you should check P/V since the heads you are running are questionable on the milling.I'm pretty sure that Cam has XER lobes and I had it cut kind of wierd.
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)