hand ported (pics)
hand ported (pics) what do you guys think of this job? I didn't do it but have the chance to buy them cheap!
intake 200-156, 300-212, 400-263, 500-295, 550-305, 600-311, 650-turbulant
exhaust 200-112, 300-134, 400-168, 500-195, 550-207, 600-212, 650-did not flow
that's the flow numbers....well
intake 200-156, 300-212, 400-263, 500-295, 550-305, 600-311, 650-turbulant
exhaust 200-112, 300-134, 400-168, 500-195, 550-207, 600-212, 650-did not flow
that's the flow numbers....well
I dont know about the intake flow #s. Its capable with a stock size valve but dont know about that pic, kinda hard to tell. But you cannot look at a port and know what it flows anyhow lol. The seat sizes look like 2.00/1.55
yeah they are the stock size valves, they have done a valve job to both intake and exhaust. other then the porting that's it. I was a little sceptical of the flow numbers but they look decent and the price is right!
Originally Posted by Flamed_Chevelle
yeah they are the stock size valves, they have done a valve job to both intake and exhaust. other then the porting that's it. I was a little sceptical of the flow numbers but they look decent and the price is right!
I would be cautious. I bought a used set of LS6 heads from a member on this board "Minty" that were suppost to be great. They were a POS! I should have bought a NEW set of AFR heads. They would have been cheaper and alot less of a headache! Watch out on those good deals. Good luck. Andy
Originally Posted by LASTLS1
I would be cautious. I bought a used set of LS6 heads from a member on this board "Minty" that were suppost to be great. They were a POS! I should have bought a NEW set of AFR heads. They would have been cheaper and alot less of a headache! Watch out on those good deals. Good luck. Andy
If this person can't print out flow numbers I would run away from them. Even then you're still taking a big chance on the actual performance. Your call, but don't bitch about them if they suck.
Trending Topics
Originally Posted by DrkPhx
I agree. If it seems to good to be true; it is. Especially from a private seller. You have no way of knowing if it's no good or not until it's too late. Since used parts are sold "as-is" you will be screwed if the heads turn out to be junk.
If this person can't print out flow numbers I would run away from them. Even then you're still taking a big chance on the actual performance. Your call, but don't bitch about them if they suck.
If this person can't print out flow numbers I would run away from them. Even then you're still taking a big chance on the actual performance. Your call, but don't bitch about them if they suck.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Originally Posted by DrkPhx
I agree. If it seems to good to be true; it is. Especially from a private seller. You have no way of knowing if it's no good or not until it's too late. Since used parts are sold "as-is" you will be screwed if the heads turn out to be junk.
If this person can't print out flow numbers I would run away from them. Even then you're still taking a big chance on the actual performance. Your call, but don't bitch about them if they suck.
If this person can't print out flow numbers I would run away from them. Even then you're still taking a big chance on the actual performance. Your call, but don't bitch about them if they suck.