Ms4
#41
FormerVendor
iTrader: (7)
Join Date: Apr 2003
Location: Lubbock
Posts: 1,106
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by jinxedz
put a 'everything id need for a cam swap' package together and you have a customer ...
Complete Cam Install Kit which includes all necessary GM bolts/gaskets for installation = 43.99
Throw some shipping in there and depending on if you need oil pump/timing set that is the total cost you would be looking at minus oil/coolant.
Let me know if you have any more questions!!
Zach
#42
As much respect I have for TSP and its products. But this logo sounds little too rice. 82 fly wheel HP? You should just do rwhp before and after on a stock cam with full boltons vs a tuned MS4 cam. Post little more under the curve power vs peak power.
Remember all honda civic with turbo makes 500 fwhp and run 13's.
#45
TECH Addict
iTrader: (48)
Originally Posted by Zach@Texas-Speed
MS4 camshaft, PRC Dual Valve Spring Kit w/ Titanium Retainers, Hardened Pushrods = 689.99.
Complete Cam Install Kit which includes all necessary GM bolts/gaskets for installation = 43.99
Throw some shipping in there and depending on if you need oil pump/timing set that is the total cost you would be looking at minus oil/coolant.
Let me know if you have any more questions!!
Zach
Complete Cam Install Kit which includes all necessary GM bolts/gaskets for installation = 43.99
Throw some shipping in there and depending on if you need oil pump/timing set that is the total cost you would be looking at minus oil/coolant.
Let me know if you have any more questions!!
Zach
#46
This cam sounds like the perfect stop gap for my stock '00 LS1 until I get the money for the low compression (read: blower) 402 this winter. My question is, would this be a fitting cam for a larger cube/SC'd motor later on? I'm guessing no, and that's not a big deal but it would be sweet if it was!
#49
FormerVendor
iTrader: (7)
Join Date: Apr 2003
Location: Lubbock
Posts: 1,106
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by mousetom78
As much respect I have for TSP and its products. But this logo sounds little too rice. 82 fly wheel HP? You should just do rwhp before and after on a stock cam with full boltons vs a tuned MS4 cam. Post little more under the curve power vs peak power.
Remember all honda civic with turbo makes 500 fwhp and run 13's.
Believe it or not, but 82fwhp is what the gains were on an engine dyno. This was a before and after test from a stock cam to the MS4.
We have been doing rwhp numbers as well, but by doing an engine dyno it weeds out all the little variables that come into play.....it shows the true power being made over a stock cam when you can swap cams in 30 minutes and see the gained power. What is more true than that??
Also, Like Jason posted earlier our last test car gained 72 rear wheel horsepower with the MS4 & underdrive pulley
Last edited by Zach@Texas-Speed; 06-04-2006 at 09:17 PM.
#50
FormerVendor
iTrader: (7)
Join Date: Apr 2003
Location: Lubbock
Posts: 1,106
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Superjoe
This cam sounds like the perfect stop gap for my stock '00 LS1 until I get the money for the low compression (read: blower) 402 this winter. My question is, would this be a fitting cam for a larger cube/SC'd motor later on? I'm guessing no, and that's not a big deal but it would be sweet if it was!
This cam will work with stock heads
#51
FormerVendor
iTrader: (7)
Join Date: Apr 2003
Location: Lubbock
Posts: 1,106
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by a98ws6
How about if this cam is based towards stock heads/pistons or HC setups???
This cam picked up huge numbers coming from a stock cam and using the stock heads. So this cam does work great with stock heads/pistons and the same can be said for a HC setup.
Zach
#54
TECH Enthusiast
iTrader: (4)
Join Date: Nov 2001
Location: Atlanta, GA
Posts: 527
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Zach@Texas-Speed
Also, Like Jason posted earlier our last test car gained 72 rear wheel horsepower with the MS4 & underdrive pulley
#55
12 Second Club
iTrader: (18)
Join Date: Apr 2006
Location: Sarasota & Lee County
Posts: 627
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by REDWS6ROCKET
zach, any numbers with prc stage 1 ls6 heads and the ms4 yet. i would think that it that combo would put down some stout numbers!
I am very interested in seeing numbers for this combo: Pacesetter headers, PRC stage 1 LS6 heads with stock valves (non-comp job), MS4 cam, LS1 intake.
By showing number for this combo, poeple with better intakes know they should see more power... Also, as I stated before, the budget builders will love this combo.
Seems like TSP has been hard at work lately, they came out with a great head, then they made it better, now a cam that looks like it will dominate on the streets. Cant wait to see some numbers and see what they come out with next
#58
TECH Regular
iTrader: (4)
Join Date: Jul 2004
Location: Blue Springs, MO
Posts: 471
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by BLACKNREDSS
im tempted to send back the torquer for this beast
#59
12 Second Club
Thread Starter
Join Date: Jun 2005
Location: Kansas City, MO
Posts: 1,275
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by REDWS6ROCKET
i woudn't just keep your set up, i see how good stangkilr's runs with an auto. your car is going to scream