cam choice for 408
#1
8 Second Club
Thread Starter
iTrader: (76)
Join Date: Jun 2004
Location: Goshen NY
Posts: 2,902
Likes: 0
Received 0 Likes
on
0 Posts
cam choice for 408
Herese the run down, 12.5 to 1 with a set of ETP 245 heads , 90/90 setup posibly sheetmetal intake. Im still up in the air to go solid roller or stay hyd roller. car isent driven much so the sky is the limit on cam choice
Trending Topics
#8
Staging Lane
Join Date: Jun 2005
Location: Australia victoria
Posts: 67
Likes: 0
Received 0 Likes
on
0 Posts
Running a Comp 250/254 on a LSA of 110 ICL of 106 on my set up, not yet tuned still using a stock auto tune and idles at 900rpm when hot, drives very well. I originaly ran a 244/248 on a LSA 112. I would seriously look at diff gearing using a cam over 250 dur as I went with 4.11:1 on a four door Holden Commodore here in Australia.
#10
TECH Enthusiast
iTrader: (5)
Join Date: Jul 2004
Location: cali
Posts: 610
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by kumar75150
got a 253 261 .640ish lift cam on a 113lsa from Futral/Cam Motion for my 408
what kind of result did you get?? just bought one from them a little smaller. 250/257 640ish..
#11
TECH Enthusiast
iTrader: (5)
Join Date: Jul 2004
Location: cali
Posts: 610
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by 1984camaroz28
Herese the run down, 12.5 to 1 with a set of ETP 245 heads , 90/90 setup posibly sheetmetal intake. Im still up in the air to go solid roller or stay hyd roller. car isent driven much so the sky is the limit on cam choice
i would give allen at futral a call or erik koening at HPE.. their pretty busy all the time but they'll give you good advice.
#12
8 Second Club
Thread Starter
iTrader: (76)
Join Date: Jun 2004
Location: Goshen NY
Posts: 2,902
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by kumar75150
got a 253 261 .640ish lift cam on a 113lsa from Futral/Cam Motion for my 408
#13
T-rex or the MS4 would pair nicely with that setup. Just do a search and you will find several posts on it. There was one recently that had a poll so check that one out.
#14
11 Second Club
iTrader: (42)
Join Date: Jun 2006
Location: Bryant,Ar.
Posts: 689
Likes: 0
Received 0 Likes
on
0 Posts
Look at your goals...is it N/A, or is it a no2 motor......I'm running a small cam 244/250 630/630 on a 114+2...Very streatable, built for n2o..and runs like scolded ape **** on motor.....You can have your cake and eat it too...lots of cam options....best of luck
#16
10 Second Club
iTrader: (8)
Join Date: Mar 2004
Location: McLean, VA
Posts: 262
Likes: 0
Received 0 Likes
on
0 Posts
i'll add my question to this post as well....i plan on doing a 408 also with the AFR 225's. what are the pros/cons to doing a solid roller vs. hyd. roller? im planning on spraying eventually and basically want to have a street brawler. i just had 4.30s put in the 12 bolt so thats the gear i'll be running. thanks
#17
11 Second Club
iTrader: (14)
Join Date: Aug 2003
Location: Kentucky
Posts: 930
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by kumar75150
got a 253 261 .640ish lift cam on a 113lsa from Futral/Cam Motion for my 408
#18
8 Second Club
Thread Starter
iTrader: (76)
Join Date: Jun 2004
Location: Goshen NY
Posts: 2,902
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by chrismcdaniel
i also got a custom cam motion cam for my 408, slightly larger than that, but in the same ballpark 257/264 646/646 112