4-Barrel EFI on 400 cube plus motors???
#1
TECH Regular
Thread Starter
Join Date: May 2008
Location: St.Louis Missouri
Posts: 460
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I'm looking into getting a Vic Junior Intake & a Edelbrock 4-Barrel TB with a plate kit for my 408, but i haven't seen many posts on people running this set-up on the street? Anyone have any suggestions on it?
#2
OWN3D BY MY PROF!
iTrader: (176)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I just got my throttle body in the mail the yesterday. I am going to eventually be running a super vic with an accufab 1550cfm 4150 throttle body. I have the intake, TB, crank, rods, pistons, lifters and valve springs. I still need a block, pushrods, retainers, locks, cam, bearings, rings, the rest of the dry sump parts and to have it all put together. It is a long way down the road. Look around for results. They are out there.
#3
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Make sure you get one that flows at least 1500 like Beaflag's. I have a stout 406 sbc chev with efi and Holleys 1000 cfm tb on a victor jr. I think it is holding the engine back quite a bit. It works great and has super response. It is a solid roller engine that pulls well past 7,000 rpm. I probably need a super victor with a larger tb.
#4
10 Second Club
iTrader: (3)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I just got my throttle body in the mail the yesterday. I am going to eventually be running a super vic with an accufab 1550cfm 4150 throttle body. I have the intake, TB, crank, rods, pistons, lifters and valve springs. I still need a block, pushrods, retainers, locks, cam, bearings, rings, the rest of the dry sump parts and to have it all put together. It is a long way down the road. Look around for results. They are out there.
Which one did you end up getting? I was told my accufab 4150 only flowed 1250.
#6
10 Second Club
iTrader: (3)
Join Date: Mar 2005
Location: Rancho Cucamonga, CA
Posts: 596
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here is the info for each
Victor Jr = http://www.summitracing.com/parts/ED...6/?image=large
Super Victor = http://www.summitracing.com/parts/ED...5/?image=large
Basic difference is runner size and length, and fitment under standard hood.
Victor Jr = http://www.summitracing.com/parts/ED...6/?image=large
Super Victor = http://www.summitracing.com/parts/ED...5/?image=large
Basic difference is runner size and length, and fitment under standard hood.
#7
OWN3D BY MY PROF!
iTrader: (176)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
![](http://img32.imageshack.us/img32/3873/accell1550cfm4150.jpg)
Trending Topics
#8
10 Second Club
iTrader: (3)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I made an error posting that. I was typing that response out around 5am in the morning during my overnight shift at work. The throttle body I have is actually an accell. This is what it looks like and seeing it you can tell why it flows the extra 300ish cfm over a 4 bbl style:
![](http://img32.imageshack.us/img32/3873/accell1550cfm4150.jpg)
![](http://img32.imageshack.us/img32/3873/accell1550cfm4150.jpg)
Gotcha. That thing will definately outflow mine. The accufab has alot of material in the "bowl" area.
#10
11 Second Club
iTrader: (18)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
you are going to be cutting a lot of cowl with a plate kit, victor jr, and 4150 tb. You might lose a wiper....
Alternatives: Run the shorter intake, i.e. the GMPP one
or
Instead of a plate kit, get in contact with nitrous outlet on here. they can plumb with victor jr with a spray bar. pretty much a plate kit built into the intake. That way you won't have to run the plate/spacer between the intake and throttle body, and will give you more clearance
Alternatives: Run the shorter intake, i.e. the GMPP one
or
Instead of a plate kit, get in contact with nitrous outlet on here. they can plumb with victor jr with a spray bar. pretty much a plate kit built into the intake. That way you won't have to run the plate/spacer between the intake and throttle body, and will give you more clearance
#14
10 Second Club
iTrader: (1)
Join Date: Nov 2001
Location: Boggy Creek
Posts: 1,528
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I have that setup on my 370 ci motor. Victor Jr intake,Edelbrock 4150 throttle body and Zex parimeter plate kit on a NOS wet system.
When i was looking for throttle bodies i got caught up in the flow quotes. It's no different in people pushing their products by inflateing numbers to make their's just a bit better than the other. Most all of these TB are dead even with each other on flow and all the 4150 i have seen have 1 3/4 inch butterflies,so you choose which one you want.
When i was looking for throttle bodies i got caught up in the flow quotes. It's no different in people pushing their products by inflateing numbers to make their's just a bit better than the other. Most all of these TB are dead even with each other on flow and all the 4150 i have seen have 1 3/4 inch butterflies,so you choose which one you want.
#18
10 Second Club
iTrader: (1)
Join Date: Nov 2001
Location: Boggy Creek
Posts: 1,528
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
The regular sunoco will fit but it will be tight and the lip of the cowl towards the front glass will not cover the carb hat completely. I sold my sunoco to a buddy and bought the wide version to cover the intake completely along with it being taller to have enough room for the nitrous plate.