Harland Sharp L92 Roller Rockers
Thread Starter
11 Second Club
Joined: May 2007
Posts: 226
Likes: 1
From: Sydney
Harland Sharp L92 Roller Rockers Does anyone have any info on the new Harland Sharp RR's to suit a L92 head ?
I did hear they were available but as yet can't find any details on them.
Any help would be much appreciated.
cheers
I did hear they were available but as yet can't find any details on them.
Any help would be much appreciated.
cheers
they are doing stock LS7 rockers for $250 ish. came highly recommended by both steve at R.E.D. and Richard of WCCH.
www.harlandsharp.com
www.harlandsharp.com
This came from HS on 11/26
I included his contact information if you wanted to talk to him directly.
We have developed a roller rocker system for the L92 heads and to the best of my knowledge the LS3 uses the same head. The only mods that need to be done are extra clearance on the head, around the pushrod side of the rocker. For a 1.8:1 ratio you need to order part# SL928 and the cost is $535.00. I can ship a set in about a weeks’ time. Thanks
Randy Becker Jr.
Harland Sharp Roller Rockers
19769 Progress Dr.
Strongsville, OH 44149
(440)238-3260
I included his contact information if you wanted to talk to him directly.
We have developed a roller rocker system for the L92 heads and to the best of my knowledge the LS3 uses the same head. The only mods that need to be done are extra clearance on the head, around the pushrod side of the rocker. For a 1.8:1 ratio you need to order part# SL928 and the cost is $535.00. I can ship a set in about a weeks’ time. Thanks
Randy Becker Jr.
Harland Sharp Roller Rockers
19769 Progress Dr.
Strongsville, OH 44149
(440)238-3260
Thread Starter
11 Second Club
Joined: May 2007
Posts: 226
Likes: 1
From: Sydney
Yep thats almost the same email I got from Randy Becker. Heads will have the notches done by Richard from WCCH but for the moment I will keep the stockers in there and let someone else test the Harland Sharps
cheers
cheers
When my 416 L92 was built, there was only two options. 1. use the stock L92 rockers, and 2. have Harland Sharp upgrade the stock rockers. I went with option 2, so far s good.
Trending Topics
I have a set of stockers from my 317 heads that I pulled to make way for the L92's. Can I use these on my new heads? (except for the new 8 offset ones I need) and what does H-S do to the stockers to improve them, and lastly what is the cost? Thanks
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo Correct, you can use the 8 stock (317 heads) rockers on the exhaust valves. You will need the new offset rockers and pedistals for the L92 heads though.
