ported ls7 heads
#42
Staging Lane
Thread Starter
Yeah I did, for a short time, missed it to much. the only thing that I really love doing. as far as working goes. spent a lot of time on this setup..its a beast now. with the intake I have know doubt it will make 650 to the ground and on mustang dyno thats strong, stock ci ls7 on pump 93...ppl will be seeing this car. i'm damn proud of it.
Last edited by z0sicktanner; 02-09-2017 at 07:29 PM.
#44
Chad you did a FAST LS7 intake for me that had huge gains over the stock 102. Have you played around with any MSD intakes for the LS7?
Also, I would love to see a CID intake on the setup in this thread. A local guy is putting together a setup that uses one and I'm looking forward to his results.
I should have mine back on he dyno next week. Shooting for similar numbers with a plastic intake. I haven't pulled the trigger on an EWP yet, hoping I can leverage some E85 to clip 630rwhp.
Great work as usual my friend!
Also, I would love to see a CID intake on the setup in this thread. A local guy is putting together a setup that uses one and I'm looking forward to his results.
I should have mine back on he dyno next week. Shooting for similar numbers with a plastic intake. I haven't pulled the trigger on an EWP yet, hoping I can leverage some E85 to clip 630rwhp.
Great work as usual my friend!
#45
Staging Lane
Thread Starter
Chad you did a FAST LS7 intake for me that had huge gains over the stock 102. Have you played around with any MSD intakes for the LS7?
Also, I would love to see a CID intake on the setup in this thread. A local guy is putting together a setup that uses one and I'm looking forward to his results.
I should have mine back on he dyno next week. Shooting for similar numbers with a plastic intake. I haven't pulled the trigger on an EWP yet, hoping I can leverage some E85 to clip 630rwhp.
Great work as usual my friend!
Also, I would love to see a CID intake on the setup in this thread. A local guy is putting together a setup that uses one and I'm looking forward to his results.
I should have mine back on he dyno next week. Shooting for similar numbers with a plastic intake. I haven't pulled the trigger on an EWP yet, hoping I can leverage some E85 to clip 630rwhp.
Great work as usual my friend!
This was going with my runner no other changes
and the CID intake you speak of note how straight those runners are see light in all 4 ports. also runners going downhill and not much flat flooring= high rpm hp
Last edited by z0sicktanner; 02-11-2017 at 01:16 PM.
#48
Staging Lane
Thread Starter
and the way it will be ran. tests have already been done on the street with 5-6 cars diff from last setup...now this look isnt for everybody...but power was what we was looking for here and on a a budget...as the car never sees rain anyway. and its main use is drag and 1/2 mile events.
Last edited by z0sicktanner; 02-13-2017 at 10:19 PM.
#49
Staging Lane
Thread Starter
few adjustments made, Well I think its safe to say this car will get air for tx2k!! Thats a 6 inch inlet. wouldn't be surprised if the car picks up a pound of boost at speed lol. cant wait to see this thing run..
#54
Staging Lane
Thread Starter
Ian was back at straightline to add fuel up top was going lean at speed. this is the graf. dotted line is preport solid line after porting of intake. only diff was first pulls i have in this thread was on 26'inch tires. he used 28's on this pull. i'm sure this affected the number some how much not sure. gained power and tq everywhere but lost 7hp in the last 400rpm's i'm sure some of that was from fattening the afr ...gained 34 tq to the wheels down low and 24 peak same dyno
Last edited by z0sicktanner; 02-24-2017 at 07:47 AM.
#55
Interesting results. Nice gains down low, now the little loss on top could be due to the rotational mass due to the larger tire?
Are the 26"s still available?
Is that with your ported heads? Which cam? What is the ICL? I expected to "peak" higher in the RPM range, something like 7300 or so.
Are the 26"s still available?
Is that with your ported heads? Which cam? What is the ICL? I expected to "peak" higher in the RPM range, something like 7300 or so.
#56
Staging Lane
Thread Starter
Interesting results. Nice gains down low, now the little loss on top could be due to the rotational mass due to the larger tire?
Are the 26"s still available?
Is that with your ported heads? Which cam? What is the ICL? I expected to "peak" higher in the RPM range, something like 7300 or so.
Are the 26"s still available?
Is that with your ported heads? Which cam? What is the ICL? I expected to "peak" higher in the RPM range, something like 7300 or so.
yes all these numbers and all work posted is what I did to the heads an intake...the plan was to make power till 7300 with the air intake outside the hood it was showing 13.5 afr at 100 plus on wideband but on the dyno it didnt show lean...so had to be fattened up so it wont go lean at speed...I'm not a tuner so I'm not 100% sure how much the numbers it would throw off...the black lines at bottom show afr solid line is now, the dotted was before intake port...tires will affect numbers the 28" is ten lbs more than the 26...he is gonna be putting the 26's back on and do another pull...not sure when but i'll post when i get the numbers. even if the numbers fail it will be posted...traps speeds and track info i will share as well.. cam used is the lumberjack cam..the kpa is dropping to 94 up top..not sure why..but it did the same before we ported intake..i'll see if i can get Michael Hornback from straightline to answer some ?s..or to answer what i posted i'd like to hear his take as well.
Last edited by z0sicktanner; 02-24-2017 at 03:04 PM.
#57
Staging Lane
Thread Starter
test hit 30-120 pull The car went from 30 to 120 in 6 sec. with tire spin. 140 plus trap car...I have Cash on this bet..ha ha.
Last edited by z0sicktanner; 03-04-2017 at 05:39 PM.