L92 Chambers

Reply Subscribe

Thread Tools

Search this Thread

Apr 29, 2007 | 06:17 PM

the_merv

Thread Starter

11 Second Club

iTrader: (88)

Joined: Mar 2006

Posts: 21,019

Likes: 893

From: The Beach...

L92 Chambers

I know that the L92 Heads from the Factory are ~70cc Chambers. I just got mine milled down .025(25 thousanths), anyone have a chart or something like that to figure out what the Chambers will be now. I figured around 66.3 by going off of what other people have posted..

Apr 29, 2007 | 08:13 PM

WKMCD

TECH Junkie

iTrader: (2)

Joined: Mar 2005

Posts: 3,416

Likes: 2

From: Northern VA

Figure about 1cc for every .010 mill.

Apr 29, 2007 | 08:44 PM

the_merv

Thread Starter

11 Second Club

iTrader: (88)

Joined: Mar 2006

Posts: 21,019

Likes: 893

From: The Beach...

I read it was a little more than that.. I am trying to get a definate answer on it.
Someone here was a talking about how they milled theirs down .030, and they got 65cc Chambers. I was hoping that who posted that would chime in..

Apr 29, 2007 | 09:48 PM

03 BUSA

10 Second Club

iTrader: (25)

Joined: Dec 2004

Posts: 2,554

Likes: 1

From: Kannapolis, NC

I thought it was for every.006 milled equalled 1 cc. But after reading the above thread I am confused. The .006 = 1cc sounds right though.

Apr 29, 2007 | 10:05 PM

the_merv

Thread Starter

11 Second Club

iTrader: (88)

Joined: Mar 2006

Posts: 21,019

Likes: 893

From: The Beach...

That's what I got with the LT1, but the Chambers are a little different with the LSX Heads..it does sound close though.

Apr 30, 2007 | 07:00 AM

WKMCD

TECH Junkie

iTrader: (2)

Joined: Mar 2005

Posts: 3,416

Likes: 2

From: Northern VA

Quote:

Originally Posted by 03 BUSA

I thought it was for every.006 milled equalled 1 cc. But after reading the above thread I am confused. The .006 = 1cc sounds right though.

You're right...I shouldn't try to do two things at once...It is .006=1cc but this is just a ball park. You still need to cc the chambers.

Apr 30, 2007 | 07:50 AM

veee8

8 Second Club

iTrader: (40)

Joined: Aug 2005

Posts: 1,861

Likes: 0

From: Raleigh,North Carolina

What was the finish like on your heads before milling? I got the bare L92's, and the deck surface is a little rough than I am used to. What is normal?

Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?

Pouria Savadkouei

Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine

Verdad Gallardo

7 Most Reliable High-Performance Engines GM Has Ever Built

Verdad Gallardo

Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin

Verdad Gallardo

6 Common C5 Corvette Failures and What's Involved In Repairing Them

Pouria Savadkouei

Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph

Verdad Gallardo

Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked

Pouria Savadkouei

Top 10 Most Powerful Chevy Trucks Ever Made!

Hennessey's New Supercharged Silverado ZR2 Has 700 HP

Verdad Gallardo

Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes

Verdad Gallardo

Apr 30, 2007 | 03:23 PM

MrEracer

On The Tree

iTrader: (3)

Joined: Dec 2001

Posts: 115

Likes: 2

From: Aguila, Arizona, USA

I milled my L92 heads .020" and then cc'd them and they are now 66cc.
Shirl Dickey

May 1, 2007 | 07:20 PM

#10

veee8

8 Second Club

iTrader: (40)

Joined: Aug 2005

Posts: 1,861

Likes: 0

From: Raleigh,North Carolina

Where yours the bare castings, or the assembled heads? Both castings have a rougher than normal look to them.

May 1, 2007 | 10:11 PM

#11

the_merv

Thread Starter

11 Second Club

iTrader: (88)

Joined: Mar 2006

Posts: 21,019

Likes: 893

From: The Beach...

The newer ones are rougher, the earlier castings are smooth. I got a old one and a new one when I got mine. The Ports and Chambers are good though..both smooth.

May 2, 2007 | 05:50 PM

#12

veee8

8 Second Club

iTrader: (40)

Joined: Aug 2005

Posts: 1,861

Likes: 0

From: Raleigh,North Carolina

So do they need a finish cut before assembly? Has anyone else noticed the rough finish on the deck surface? Anyone know the price on those Manley valves for the L92?

May 2, 2007 | 10:24 PM

#13

the_merv

Thread Starter

11 Second Club

iTrader: (88)

Joined: Mar 2006

Posts: 21,019

Likes: 893

From: The Beach...

My Deck Surface was smooth.

May 5, 2007 | 01:27 PM

#14

veee8

8 Second Club

iTrader: (40)

Joined: Aug 2005

Posts: 1,861

Likes: 0

From: Raleigh,North Carolina

They are smooth, but its almost like they have a slightly steeper RA to grip the gaskets or something. They are beautifully machined just slightly irregular.