Got my SHorter Dogbone, One Question
#7
TECH Addict
Thread Starter
iTrader: (5)
Join Date: Jun 2009
Posts: 2,802
Likes: 0
Received 0 Likes
on
0 Posts
Where do you put the prybar? I can't find anywhere that doesn't have hoses and wires. I tried jacking up the back but it won't quite make it. This sucker's at LEAST an inch shorter hole to hole, I'm worried that the engine won't rock that far.
Last edited by AlabamaGuy; 08-13-2009 at 10:47 PM.
Trending Topics
#8
LS1Tech Sponsor
did you order the correct one????
I'd be worried about having to tweak/angle the engine that much more forward and putting more stress on the tranny...
I'd be worried about having to tweak/angle the engine that much more forward and putting more stress on the tranny...
__________________
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
#9
That's why you need to put the trans in N before atempting to move the engine. 06MonteSS is on to something tho, if it is that much shorter it may pu a bind on the trans mount.
#15
TECH Enthusiast
When you lower a W-Body with a 3800 the engine sits lower/at a different angle then factory.
So these move the engine forward to help re leave stress on the drive train and on the rack.
So these move the engine forward to help re leave stress on the drive train and on the rack.
#18
I talked to Mike and he said he doesn't know if it will work. He said the best advice is to measure the length of your stocker and that of a 3800 to see if those are the same to start with. If they aren't then that should give you an answer. If they are then it might work but he isn't sure as it has never been officially tested.
Hope that helps,
John
Hope that helps,
John
#19
TECH Junkie
iTrader: (1)
Join Date: Jun 2007
Location: New Orleans La
Posts: 3,159
Likes: 0
Received 0 Likes
on
0 Posts
These are the ones I have and you can buy just one
http://www.3800performance.com/Merch...roduct_Count=4
http://www.3800performance.com/Merch...roduct_Count=4
#20
TECH Addict
Thread Starter
iTrader: (5)
Join Date: Jun 2009
Posts: 2,802
Likes: 0
Received 0 Likes
on
0 Posts
I talked to Mike and he said he doesn't know if it will work. He said the best advice is to measure the length of your stocker and that of a 3800 to see if those are the same to start with. If they aren't then that should give you an answer. If they are then it might work but he isn't sure as it has never been officially tested.
Hope that helps,
John
Hope that helps,
John