Bent Suspention!
TECH Enthusiast
Joined: Apr 2007
Posts: 697
Likes: 0
From: Hudson River Valley, NY
Well I have this...
http://www.fquick.com/images/vehicle...jpg?1205600052
http://www.fquick.com/images/vehicle...jpg?1205600051
http://www.fquick.com/images/vehicle...jpg?1205600388
They aren't dead on....Unless somone has a better shot....
http://www.fquick.com/images/vehicle...jpg?1205600052
http://www.fquick.com/images/vehicle...jpg?1205600051
http://www.fquick.com/images/vehicle...jpg?1205600388
They aren't dead on....Unless somone has a better shot....
Last edited by Count of Monte Carlo; Apr 9, 2008 at 08:16 AM.
Thread Starter
TECH Fanatic
Joined: Jun 2007
Posts: 1,316
Likes: 3
From: Dolla$ , TX
Dealership said they can't warranty it , they said GM wil want the part back and they will end up being charged once they see it was due to road conditions so i'm just going to order 1 BMR lateral arm and replace em as they bend lol
Thread Starter
TECH Fanatic
Joined: Jun 2007
Posts: 1,316
Likes: 3
From: Dolla$ , TX
No these parts only move in one direction as long as i have a alignment done after also this oem one is bent to **** and i don't notice anything. Besides the OEM one is 100 bucks cheaper and i think i might just replace it with OEM cause i doubt this will happen again.
Yes, it takes them FOREVER to ship...almost 3 weeks on the STB's I ordered and a month on the TPMS sensors. If you become an active member at NAIOA, ZSPOT might be able to cut you a break on the part.
Or you can sign up at ClubGP and order from Monster Parts.
However, I can't imagine there's not a GM supporting vendor here to order from...so check it out. (Maybe www.SDPC2000.com or http://www.gmperformancepartszone.com/)
Or you can sign up at ClubGP and order from Monster Parts.
However, I can't imagine there's not a GM supporting vendor here to order from...so check it out. (Maybe www.SDPC2000.com or http://www.gmperformancepartszone.com/)
LS1Tech Sponsor
Joined: Dec 2005
Posts: 2,932
Likes: 12
From: CT
I was working on my exhaust cutout because it had seized up from rust while iw as under the car i got to noticing one of the control arms "i think thats what its called" was bent probably from a hitting the dear a few months ago! I looked on the other side and its bent to accept the one towards the rear of the car accept the one towards the front. Hopefully my warranty will cover this!
yeah, reviving an old thread here...
how the hell did that get bent??
I've just got done hitting some BAD potholes and "speed bumps" on the highway doin 50-60mph, and just checked my **** out... everything is still fine and straight...
__________________
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
LS1Tech Sponsor
Joined: Dec 2005
Posts: 2,932
Likes: 12
From: CT
aaah, ok... that makes me feel better... heh..
yeah, cuz they're doing work on the highways around here... grinding it down and re-paving.... well, eastbound, the ridge between the grinding and the old road, they didn't smooth out the transition so well, and it's a friggin speed bump, and I mean HARD....
thought my front/rear end was gonna fall off...
but after looking at everything from underneath tonight, everything is still straight and tight...
whew!!!
nothing like what the pictures show in this thread...
heh...
yeah, cuz they're doing work on the highways around here... grinding it down and re-paving.... well, eastbound, the ridge between the grinding and the old road, they didn't smooth out the transition so well, and it's a friggin speed bump, and I mean HARD....
thought my front/rear end was gonna fall off...
but after looking at everything from underneath tonight, everything is still straight and tight...
whew!!!
nothing like what the pictures show in this thread...
heh...
__________________
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
10 Reasons the LS7 Is GM's Most Extreme Naturally Aspirated V8 Engine Ever
Verdad Gallardo LS1Tech Sponsor
Joined: Dec 2005
Posts: 2,932
Likes: 12
From: CT
yeah, searched before and found that pic too... ny **** DEFINITELY doesn't look like that...
don't even have the small curve/bend that the OP has...
so I'm good...
whew!!
hehe
don't even have the small curve/bend that the OP has...
so I'm good...
whew!!
hehe
__________________
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
06MonteSS / DiabLew Tune
2014 Camaro 2SS/RS - LS3, 6-speed manual, short-throw performance shifter, NPP dual-mode performance exhaust, 1LE front splitter, ZL1 rockers, Z28 Rear Spoiler, all paint-matched Red Rock Metallic, BMR strut tower brace, Cold Air Inductions cold air intake, Apex Motorsports, Inc. catch-can, Custom DiabLew Tune
www.diablewtune.com -- www.diablocustomtune.com -- www.diablocustomtunegm.com
Thread Starter
TECH Fanatic
Joined: Jun 2007
Posts: 1,316
Likes: 3
From: Dolla$ , TX
I think it was from doing several 360's after clipping a deer. I actually havn't replaced it yet i will be buying the part tomorrow odd timing. I just bought the haynes manual to make sure there wasn't anything special i needed to do to remove it. They do recommend you drop the crossmember on the side your replacing and leave the other side bolted up. I don't really know a safe place to put the jack to hold the rear up besides on the suspention. There are the pinch weld spots where the unibody is for the OEM jack but i'm afraid i'll bend the metal if i put my jack there. Maybe i can get a adapter for the jack that will fit.
