Forged Built APS Twin Turbo PART OUT!
#1
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Give me a few days on the stuff. In a week this car wil be disassembled and gone and all the parts will be in my garage ready to ship out. I cannot accept any money yet as they are still on the car, but in a week or sothey should all be ready to go. If your interested in parts at my asking price, i will place your name beside the part and you will be first in line. If you have an offer, i will put you in line accordingly with an *. Thanks!
ENGINE
Forged 347
LS6 block, stock crank, Diamond -1.6cc pistons, Callies Rods, Total Seal Rings, ARP hardware, ARP head stud kit, Patriot 6.0l 72cc heads with patriot dual gold valvesprings, custom comp cam, comp hardened pushrods, n-motion double roller timing set, ported ls6 oil pump, ls7 lifters, stock rockers, ls6 intake painted gloss black, valve covers painted gloss black. Complete Intake to oil pan, no accessories (CAN INCLUDE IF NEEDED!) Engine has great oil pressure and has just been broken in properly by EPP. Has only roughly 600 miles on it. Shortblock was built by Billy Briggs from W2W! CR is roughly 9.3:1 with the 72cc heads, can be an NA or nitrous motor with a simple head change. This is complete from the intake to the oil pan with all covers, front, rear, valvecovers, ls6 valley
Buy it as you see it with coil packs, sensors - map, starter, TB, Water pump, crank pulley, PCV set-up, tensioner
SOLD
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4590.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4591.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4592.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4594.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4600.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4596.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4597.jpg)
Twin Turbos
APS F-body Twin Turbo Kit. Roughly 600 miles on it. Made 666 RWHP/640 RWTQ on a mustang dyno @ 13 psi on a 347. Has the windshield washer tank modified as a meth tank for my snow stage 2 meth injection kit. Will come with the Snow Stage 2 meth injection. There is a MAF delete pipe with a bung for the meth nozzel welded in. Other than that it is exactly what you'd get from APS! Remember, you ALSO get the Snow meth injection kit with!
SOLD
BMR Tubular K-Member. Black Hammertone. What the APS kit was based around. Will not sell until the APS kit is sold. Only on the car for 600 miles.
SOLD
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4341.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4340.jpg)
Turbosmart Eboost-2 controller. White face with black bezel. Very little use, practically brand new, works like a champ, only had the main features hooked up, never got in depth with it but you can use it to also control a meth kit, trigger on a second fuel pump, do boost by RPM, etc etc, tons of features!
SOLD
ELECTRONICS
Autometer Phantom 2 1/16" WIDEBAND A/F guage with sensor. Had it in my guage pod with the sensor in my downpipe but never wired up the power or ground to the guage so its really never been used!
SOLD
Autometer Phantom 2 1/16" Electronic Fuel Pressure guage. Has sending unit, been used with no issues!
SOLD
Autometer Phantom 2 1/16" Mechanical Transmission Temp guage with sending unit. Used with no issues!
SOLD
Autometer triple pillar guage pod. Has been painted to match the factory graphite interior panels of my 99' Trans Am
SOLD
DRIVETRAIN
Fully Built 4l60-e trans and Yank SS 3600 Converter. Purchased used but Mike @ Vortech Converters flushed it out for me. No issues, hits hard and works great! Tranny has been all done up by Mike @ Vortech Converters. I don't know much about transmission but he does. He built this to handle my twin turbo project. Has roughly 600 miles on it and not a single issue. Shifts great and drives sooo smooth with all the bushings being replaced with bearings. Will come complete from bellhousing to tailhousing to oil pan with a bung welded in for trans temp sender.
SOLD
![](http://i6.photobucket.com/albums/y231/WS6SnakeEtr/100_4099.jpg)
![](http://i6.photobucket.com/albums/y231/WS6SnakeEtr/100_4096.jpg)
![](http://i6.photobucket.com/albums/y231/WS6SnakeEtr/100_4097.jpg)
FUEL
Seimens flow matched 60# Injectors
SOLD
Custom Dual Intank Walbro 255 set-up. Was done by EPP. The bucket has been modified for 2 WalbroGS340 pumps. Will be an exhange ONLY for your stock bucket with stock working pump or aftermarket.
SOLD
If i think of anymore things i missed, i will add them later. Prices are without shipping. Would prefer to sell the engine/trans/turbo kit local but if your willing to pay shipping, i will consider.
All parts are coming off the car in perfect working condition. Do to the nature of high performance parts, everything is sold as is. Everything worked as should with no issues when removing!
Here are 2 clips of the car running. Shows the great oil pressure and you can hear the engine/idle and a quick rev.
http://media.putfile.com/cold-start-36
http://media.putfile.com/Idle-and-Rev
ENGINE
Forged 347
LS6 block, stock crank, Diamond -1.6cc pistons, Callies Rods, Total Seal Rings, ARP hardware, ARP head stud kit, Patriot 6.0l 72cc heads with patriot dual gold valvesprings, custom comp cam, comp hardened pushrods, n-motion double roller timing set, ported ls6 oil pump, ls7 lifters, stock rockers, ls6 intake painted gloss black, valve covers painted gloss black. Complete Intake to oil pan, no accessories (CAN INCLUDE IF NEEDED!) Engine has great oil pressure and has just been broken in properly by EPP. Has only roughly 600 miles on it. Shortblock was built by Billy Briggs from W2W! CR is roughly 9.3:1 with the 72cc heads, can be an NA or nitrous motor with a simple head change. This is complete from the intake to the oil pan with all covers, front, rear, valvecovers, ls6 valley
Buy it as you see it with coil packs, sensors - map, starter, TB, Water pump, crank pulley, PCV set-up, tensioner
SOLD
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4590.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4591.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4592.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4594.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4600.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4596.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4597.jpg)
Twin Turbos
APS F-body Twin Turbo Kit. Roughly 600 miles on it. Made 666 RWHP/640 RWTQ on a mustang dyno @ 13 psi on a 347. Has the windshield washer tank modified as a meth tank for my snow stage 2 meth injection kit. Will come with the Snow Stage 2 meth injection. There is a MAF delete pipe with a bung for the meth nozzel welded in. Other than that it is exactly what you'd get from APS! Remember, you ALSO get the Snow meth injection kit with!
SOLD
BMR Tubular K-Member. Black Hammertone. What the APS kit was based around. Will not sell until the APS kit is sold. Only on the car for 600 miles.
SOLD
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4341.jpg)
![](http://i291.photobucket.com/albums/ll309/Superman99ta/100_4340.jpg)
Turbosmart Eboost-2 controller. White face with black bezel. Very little use, practically brand new, works like a champ, only had the main features hooked up, never got in depth with it but you can use it to also control a meth kit, trigger on a second fuel pump, do boost by RPM, etc etc, tons of features!
SOLD
ELECTRONICS
Autometer Phantom 2 1/16" WIDEBAND A/F guage with sensor. Had it in my guage pod with the sensor in my downpipe but never wired up the power or ground to the guage so its really never been used!
SOLD
Autometer Phantom 2 1/16" Electronic Fuel Pressure guage. Has sending unit, been used with no issues!
SOLD
Autometer Phantom 2 1/16" Mechanical Transmission Temp guage with sending unit. Used with no issues!
SOLD
Autometer triple pillar guage pod. Has been painted to match the factory graphite interior panels of my 99' Trans Am
SOLD
DRIVETRAIN
Fully Built 4l60-e trans and Yank SS 3600 Converter. Purchased used but Mike @ Vortech Converters flushed it out for me. No issues, hits hard and works great! Tranny has been all done up by Mike @ Vortech Converters. I don't know much about transmission but he does. He built this to handle my twin turbo project. Has roughly 600 miles on it and not a single issue. Shifts great and drives sooo smooth with all the bushings being replaced with bearings. Will come complete from bellhousing to tailhousing to oil pan with a bung welded in for trans temp sender.
SOLD
![](http://i6.photobucket.com/albums/y231/WS6SnakeEtr/100_4099.jpg)
![](http://i6.photobucket.com/albums/y231/WS6SnakeEtr/100_4096.jpg)
![](http://i6.photobucket.com/albums/y231/WS6SnakeEtr/100_4097.jpg)
FUEL
Seimens flow matched 60# Injectors
SOLD
Custom Dual Intank Walbro 255 set-up. Was done by EPP. The bucket has been modified for 2 WalbroGS340 pumps. Will be an exhange ONLY for your stock bucket with stock working pump or aftermarket.
SOLD
If i think of anymore things i missed, i will add them later. Prices are without shipping. Would prefer to sell the engine/trans/turbo kit local but if your willing to pay shipping, i will consider.
All parts are coming off the car in perfect working condition. Do to the nature of high performance parts, everything is sold as is. Everything worked as should with no issues when removing!
Here are 2 clips of the car running. Shows the great oil pressure and you can hear the engine/idle and a quick rev.
http://media.putfile.com/cold-start-36
http://media.putfile.com/Idle-and-Rev
Last edited by Superman09; 10-03-2008 at 11:19 PM.
#4
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
PM me an offer, would rather keep the engine together as at least a longblock
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
#6
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Yes its posted above....
I will not sell it separate from the APS kit unless the APS kit is sold and the buyer doesn't need the k-member.
I've gotten a lot of interest in the fuel components and guages..... I will not sell these until i have the major items already sold. I am trying to sell the car complete as well so i am not going to part out the smaller items until i get a buyer for the bigger items to make the part out worth while. If your interested in the smaller stuff though, PM me and i will put you in line and contact you when i am ready to sell them in order of your interest
I will not sell it separate from the APS kit unless the APS kit is sold and the buyer doesn't need the k-member.
I've gotten a lot of interest in the fuel components and guages..... I will not sell these until i have the major items already sold. I am trying to sell the car complete as well so i am not going to part out the smaller items until i get a buyer for the bigger items to make the part out worth while. If your interested in the smaller stuff though, PM me and i will put you in line and contact you when i am ready to sell them in order of your interest
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
#7
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
BUMP for some very high quality parts!
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
Trending Topics
#8
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Back up for the 4th!!!!!!!!!!
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
#11
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Have a guy interested in the entire car at the moment. I will let you know how it pans out! Thanks!
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
#13
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
......?
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
#17
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Looks like the part out is a GO! Car will be coming apart here in the next few days so keep posted for more info. Get in line for your goods!
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
#20
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
ok guys, pillar pod and trans temp guages are spoken for. My buddy that is going to help me disassemble the car is getting them. ![Cheers!!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cheers.gif)
Line starts here!
![Cheers!!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cheers.gif)
Line starts here!
__________________
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed
![](https://ls1tech.com/forums/signaturepics/sigpic36191_1.gif)
Featuring 6 different turbo kits for your F-body!
Check us out on Facebook at: www.facebook.com/HuronSpeed