Lt1 stuck in the mid 11s
#1
Lt1 stuck in the mid 11s
Hey guys I posted this in the drag racing tech section but the LT1s dont get alot of attention there.
Guys I need some help with my 95 lt1 street/strip car. Last year the car was running 11.5 at 116-117. This year after removing roughly 100lbs of weight the car runs 11.5 at 115-116 .
One problem I know I have is that the car is shifting into overdrive 200ft before the end of the quarter (redlines).
The car is a stock bottom end lt1 with ported stock heads, 503 cam, 3200 vig, 3.73s with drag radials. The redline is currently set at 6400 and shift points are set at 6200, I need to raise the shift points inorder to run the whole 1/4 im wondering if I might see an ET gain from this?
Is there anything else I can do other than nos to gain something or anything?
I also posted some pics of the car (not that it will help)
Im thinkg of raising the redline to 6600 and the shift points to 6400, what do you guys think?
Guys I need some help with my 95 lt1 street/strip car. Last year the car was running 11.5 at 116-117. This year after removing roughly 100lbs of weight the car runs 11.5 at 115-116 .
One problem I know I have is that the car is shifting into overdrive 200ft before the end of the quarter (redlines).
The car is a stock bottom end lt1 with ported stock heads, 503 cam, 3200 vig, 3.73s with drag radials. The redline is currently set at 6400 and shift points are set at 6200, I need to raise the shift points inorder to run the whole 1/4 im wondering if I might see an ET gain from this?
Is there anything else I can do other than nos to gain something or anything?
I also posted some pics of the car (not that it will help)
Im thinkg of raising the redline to 6600 and the shift points to 6400, what do you guys think?
#2
TECH Fanatic
iTrader: (6)
Join Date: Oct 2007
Location: Central Valley, CA
Posts: 1,119
Likes: 0
Received 0 Likes
on
0 Posts
Flirting with disaster spinning the stock shortblock that high but I shift mine at 6500 and have yet to see any problems. If you just replace the rod bolts with ARP I have been told that you can safely spin 6500. If you increase your shift points to where you are topping out in 3rd gear at the 1/4 mile mark you should be able to pick up some MPH and shave a couple tenths. Just my .02
#3
11 Second Club
iTrader: (1)
What are your incrementals at the track? Might be easier to analyze your time slip to see where we can improve your set up. What tires are you running and what size? Have you been to the dyno to see where your torque peak is? Your converter should stall 500-700rpm below the torque peak. I think the converter may be a bit small on stall...Whats your suspension consist of? Just need a bit more info to adequately help you out...
--Alan
--Alan
#4
Hey thanks for the responses guys!
I posted a pic of one of my time slips.
Im running mt drag radials 275 50 15.
Car has not been on a dyno, the converter feels to tight but the car will usually pull the left front tire a cpl of inches and carry it for a few feet. All stock suspension with the exception of bmr lower control arms and a set of relocator control arm mounts.
I posted a pic of one of my time slips.
Im running mt drag radials 275 50 15.
Car has not been on a dyno, the converter feels to tight but the car will usually pull the left front tire a cpl of inches and carry it for a few feet. All stock suspension with the exception of bmr lower control arms and a set of relocator control arm mounts.
#6
You should immediately put subframe connectors on the car. That combined with a torque arm would net you a pretty good gain. Also I assume it hasnt been dyno tuned as you said that it hasnt been on a dyno, so a dyno tune would also help you out alot.
#7
TECH Fanatic
iTrader: (6)
Join Date: Oct 2007
Location: Central Valley, CA
Posts: 1,119
Likes: 0
Received 0 Likes
on
0 Posts
Subframe connectors and a torque arm are a good idea but they are more for cutting down 60ft times and at 1.6 I don't see that much room for improvement. I would install them just to get the torque arm off of the transmission and to reduce body flex. I still don't think you should be shifting into overdrive but you need to find out where your peak HP and torque is then adjust your stall and shift points appropriately...bottom end willing
Trending Topics
#8
Subframe connectors and a torque arm are a good idea but they are more for cutting down 60ft times and at 1.6 I don't see that much room for improvement. I would install them just to get the torque arm off of the transmission and to reduce body flex. I still don't think you should be shifting into overdrive but you need to find out where your peak HP and torque is then adjust your stall and shift points appropriately...bottom end willing
I cut a 1.4 60 ft with stock heads and a cc306 cam... I am seeing room for improvement. Plus a tenth in 60 ft is gonna be even more on the big end.
What gears are you running to be hitting overdrive at 116? Might get some arguement on this but really low gears dont seem to help LT1s too much... They tend to like to surf the torque wave
#10
I would venture to say there is some slip in your converter or transmission. I was trapping 132 MPH with a TH350 and crossing the line at 6200 RPMs. 3.73s wouldnt make that much difference.
If you have the subframes I would suggest as suggested before getting the dynotune then adjusting shiftpoints and converter.
#12
10 Second Club
iTrader: (14)
I would venture to say there is some slip in your converter or transmission. I was trapping 132 MPH with a TH350 and crossing the line at 6200 RPMs. 3.73s wouldnt make that much difference.
If you have the subframes I would suggest as suggested before getting the dynotune then adjusting shiftpoints and converter.
If you have the subframes I would suggest as suggested before getting the dynotune then adjusting shiftpoints and converter.
#15
I second that motion. Is it hitting the rev limiter before it shifts?
I have been out of the game for a couple years... having to recall how to word things the way I want
#18
TECH Fanatic
iTrader: (10)
I wouldn't just raise the shift points on a whim...get it on a dyno and see where it stops making power. The way to lower ETs is to do it methodically, not guess
Bryan (PCMforless) will without a doubt help you (call him), but you need to address your converter and dyno sheets before you do anything else, IMO.
Bryan (PCMforless) will without a doubt help you (call him), but you need to address your converter and dyno sheets before you do anything else, IMO.