CC 503 swap
Thread Starter
TECH Enthusiast
iTrader: (21)
Joined: Mar 2009
Posts: 619
Likes: 0
From: Sacramento Ca
CC 503 swap Im lookin to go from the hotcam to the 503 however im trying to make this swap as cheap as possible as i am tight on funds. The motor will already be out as I am having it rebuilt as well. I will be getting rid of the LT4 springs and also the SA rockers for a set of NSA rockers as ive heard they will be better for the new setup. So I guess my question is what are the cheapest springs i can run wit this cam and or is it possible to run an LS6 spring?! Im also looking for some cheap NSA 1.6's. I know there are plenty options out there but like i said im trying to keep this as cheap as possible. Any help help is appreciated. thanx
https://ls1tech.com/forums/lt1-lt4-m...etup-help.html
Post #6 and down from there
I used these on my CC503 and have yet to have any issues with them.
Post #6 and down from there
I used these on my CC503 and have yet to have any issues with them.
Cheapest springs? Well be careful with that stuff or your going to be pulling it apart again soon. Your best bet for good springs at a GOOD price is parts sectional and be patient. Good things don't come by the hour.
As said, I would NOT cheap out on valvetrain.. After all, horsepower is made up top!
I'd look around for a set of comp pro mags. And go for the cran 10308 Kit or the like..
I would bite the bullet though and for sure spend a few extra bucks for more security. Better safe then sorry for up top!
I'd look around for a set of comp pro mags. And go for the cran 10308 Kit or the like..
I would bite the bullet though and for sure spend a few extra bucks for more security. Better safe then sorry for up top!
Trending Topics
Thread Starter
TECH Enthusiast
iTrader: (21)
Joined: Mar 2009
Posts: 619
Likes: 0
From: Sacramento Ca
I already got the hardened pushrods but was not aware that I would need rocker studs and guideplates. Anyone know how much those are gonna run me?! thanx again
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo $26 for Guideplates: http://www.summitracing.com/parts/TFS-30400623-8/
Thread Starter
TECH Enthusiast
iTrader: (21)
Joined: Mar 2009
Posts: 619
Likes: 0
From: Sacramento Ca
Ok so now im looking on summit at comp pro mags and crane gold NSA 1.6's. Will I need shims to run either of these sets of rockers?! Also, i plan on getting a new set of LS7 lifters so with all this new stuff will i have to change pushrod length?!
