debating on stall company...
debating on stall company... I think I'd rather have one with better efficiency on the top end.
I've narrowed it down to edge or yank. Anybody WITH EXPERIENCE able to tell me which one would be better top end?
I've got a 3200 performabuilt now, but I think I'm leaving a lot on the table, one because I should be closer to 4k, and two because it was never set up for my car, just a generic 3200 build that I got with my tranny.
I've narrowed it down to edge or yank. Anybody WITH EXPERIENCE able to tell me which one would be better top end?
I've got a 3200 performabuilt now, but I think I'm leaving a lot on the table, one because I should be closer to 4k, and two because it was never set up for my car, just a generic 3200 build that I got with my tranny.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Five Reasons the Camaro Was the Most Pivotal Player in the Pony Car Wars 2.0
Brett Foote
10 Reasons the LS7 Is GM's Most Extreme Naturally Aspirated V8 Engine Ever
Verdad Gallardo
On The Tree
Joined: Jan 2004
Posts: 105
Likes: 1
I ended up buying a Coan 10" lockup converter. Interesting that someone suggested tuning it for 3rd gear lockup. I'm going to have my PCM tweaked to disable the converter clutch in 3rd gear. Are we talking about the same thing? :S lol
From my experience with Coan they seem to build their 10" max perf converters specific to a person's setup. In fact they recommend getting dyno numbers to base a converter build from, or at the very least a detailed spec list of the engine, car/chassis, and intended purpose. Give those guys a call and talk to them. I had great cs and response the few times I contacted them before making a decision. My converter was build in 2 days and shipped.
From my experience with Coan they seem to build their 10" max perf converters specific to a person's setup. In fact they recommend getting dyno numbers to base a converter build from, or at the very least a detailed spec list of the engine, car/chassis, and intended purpose. Give those guys a call and talk to them. I had great cs and response the few times I contacted them before making a decision. My converter was build in 2 days and shipped.
https://ls1tech.com/forums/automatic...l-company.html
Got all my answers over there!
Thanks for being so helpful!
https://ls1tech.com/forums/automatic...l-company.html
Got all my answers over there!
https://ls1tech.com/forums/automatic...l-company.html
Got all my answers over there!
I went from a TCI Super Street Fighter 3600 to a Yank SS3600. I dropped my ET 3 tenths and picked up 4 mph with just the Yank and no other mods.
Before I get flamed for using a TCI, I didn't know they were such junk when I got it. I ended up breaking it. I cracked the weld around the pump drive almost all the way around.
Before I get flamed for using a TCI, I didn't know they were such junk when I got it. I ended up breaking it. I cracked the weld around the pump drive almost all the way around.
BOSS APPROVED!
I bought an FTI 4400 when I was A4, never used it though.
If your setup is nothing crazy you would probably be best suited buying an "off the shelf" converter from Yank, Vig etc. You dont need anything fancy.
A good converter is ~$700 eh.
