ebay headers.
ebay headers. http://cgi.ebay.com/ebaymotors/93-97...item19c27330b9
anyone tried these?
im gona grab some cheap used headers or something like this for the lt1shootout.
i fully understand there not the best headers out there.lol
anyone tried these?
im gona grab some cheap used headers or something like this for the lt1shootout.
i fully understand there not the best headers out there.lol
http://cgi.ebay.com/ebaymotors/93-97...item19c27330b9
anyone tried these?
im gona grab some cheap used headers or something like this for the lt1shootout.
i fully understand there not the best headers out there.lol
anyone tried these?
im gona grab some cheap used headers or something like this for the lt1shootout.
i fully understand there not the best headers out there.lol
They look exactly like the ones I got from eBay seller ap1ap2. The passenger side fit without a problem, the drivers side needed alot of clearancing for the steering shaft, and very slight clearancing for the k member. Y pipe fit no problem. Overall I'm very happy with them. They tuck up nice for long tubes. Just toss the clamps they come with and get yourself some band clamps.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
12 Second Club
Joined: Feb 2006
Posts: 876
Likes: 0
From: Catlettsburg, Ky
I installed these headers on a bone stock car about 2 months ago.
I have no complaints as far as the passenger side goes. Remove the heat shield or trim it and your good to go.
The driverside needed substantial "clearancing" on the #3 or #5 primary to get the steering shaft to even go on at all, let alone actually clear. It also hit on the rear most part of the k member, and forget about an oil cooler..
The one I worked on didn't have any exhaust beyond the y pipe and I had to use the shitty clamps they came with (cheap *** customer, lol) with that said, the y pipe did hit the floor pan around the tranny crosmember area...
All in all, I guess you can't complain about stepped headers for less than $300 bucks.
I have no complaints as far as the passenger side goes. Remove the heat shield or trim it and your good to go.
The driverside needed substantial "clearancing" on the #3 or #5 primary to get the steering shaft to even go on at all, let alone actually clear. It also hit on the rear most part of the k member, and forget about an oil cooler..
The one I worked on didn't have any exhaust beyond the y pipe and I had to use the shitty clamps they came with (cheap *** customer, lol) with that said, the y pipe did hit the floor pan around the tranny crosmember area...
All in all, I guess you can't complain about stepped headers for less than $300 bucks.
very true.lol
ill keep my eyes peeled for a good used set.
i wish i had the money to buy some kooks, or ARH. but damn for a car that i plan on going turbo, i can see the money
ill keep my eyes peeled for a good used set.
i wish i had the money to buy some kooks, or ARH. but damn for a car that i plan on going turbo, i can see the money
Staging Lane
Joined: Nov 2007
Posts: 97
Likes: 0
From: Port Charlotte
ive now installed 2 sets, one on a A4 z28, and one set on a 95 m6 TA
on the TA it fit good on the pass, but number 1 primary needed denting to clear the steering shaft. owner has no other complaints except about plugs.
on the z28 passenger side hits the body of the car bad and needed the transmission ear trimmed off, same steering shaft problem on the drivers as well as it rubs on the kmember an car has a nasty vibration at idle inside. still have more work to do on the car but its not mine so dont see it often i just installed them
on the TA it fit good on the pass, but number 1 primary needed denting to clear the steering shaft. owner has no other complaints except about plugs.
on the z28 passenger side hits the body of the car bad and needed the transmission ear trimmed off, same steering shaft problem on the drivers as well as it rubs on the kmember an car has a nasty vibration at idle inside. still have more work to do on the car but its not mine so dont see it often i just installed them
The current ebay headers are hit and miss, more miss usually. The old ones from eworldsales were very good. 6LITEREATER on here had a hand in the design of them. 2 of my friends have them and fit well.
I just sent a message to 'eworldsales1' to see if he still could get his headers or where they can be found... I just noticed theres also 'epartsgogo' selling headers too but they look like every other set available
considering EVERY listing for stainless LT1 headers has the same design, same pics, and weird blue clamps, I'm willing to bet they're all from the same mfgr
Edit: Response from 'eworldsales1' - "they're no longer made and I dont have any more"
considering EVERY listing for stainless LT1 headers has the same design, same pics, and weird blue clamps, I'm willing to bet they're all from the same mfgr
Edit: Response from 'eworldsales1' - "they're no longer made and I dont have any more"
Last edited by VinR1; Jan 19, 2011 at 12:17 PM.
TECH Fanatic
Joined: Feb 2006
Posts: 1,025
Likes: 1
From: CT/NJ
26 rwhp and 31 rwft/lbs on my car from just installing these headers from stock, whole curve was higher as well, no loss anywhere. That was after bashing the snot out of the driver's side one with a 5 lb sledge to make room too. What the hell, they were only $300...
