l 95 Trans Am l

iTrader: (5)

I'm ordering my LE cam soon and I'm stumped on which rockers to get. Elliot recommended proforms because im on a budget. I've heard only good things about Scorpion rockers, what do you guys think?

Badazz 97 TA

iTrader: (18)

go with what he said. he knows what hes talking about.......

robsquikz28

iTrader: (246)

proforms work but you can find a pro magnums on here for less than 200 shipped....They are A LOT better

l 95 Trans Am l

iTrader: (5)

Yeah you might have seen my other thread about a hotcam and I decided not to go that route, and to stick to Elliots custom ground. I do think I'll be buying the proforms but I've heard people say that they had issues with them

badass383formula96

my comp cams 1.6s came apart after 25k miles spinning the motor to 7k rpms they were the full bodied almost 400.00 set. I was low on funds at the time so i threw in a set of pro form 1.6s i had laying around that had a few thousand miles on them, well that was back in august an my driving habits are the same i still spin it just as high. I just installed some prw 1.6 SA roller rockers on a buddys car they seem to be a pretty nice rocker look like a re boxed Scorpion if u ask me . Also a month ago installed summits 1.6 roller rocker they are very nice as well. all of these are fairly cheap i also had comp cams pro mags, and they didnt fit under stock valve covers without tearing the stucture out of them.

gregrob

iTrader: (8)

Comp Ultra Pro Magnums..

jlpz

iTrader: (8)

I have the scorpion 1.65/1.6 and they seem very well machined and have the clearance for the springs...I'd go scorpions or comp pro mags IMO.

hitmanws6

iTrader: (20)

I went with Comp Pro Mags

96lt1m6

iTrader: (31)

These are comp copies I have aswell as a few of my friends

96lt1m6

iTrader: (31)

These are comp copies I have aswell as a few of my friends [IMG]http://i104.photobucket.com/albums/m173/rudy_028/2010-12-24_01-29-
06_228.jpg[/IMG]
chromoly 1.6nsa,guide plates,.080 wall hardened pushrods.

Gojira94

iTrader: (4)

x2, $320.00/ set at Summit & Jegs.

The Batman

iTrader: (4)

where do you find these for sale?

96lt1m6

iTrader: (31)

pm sent

BigD383lt1

comp pro mags

95LTXZ28

iTrader: (19)

Im running 1.6 full roller harland sharp, they have been around forever and I havent had any problems with them yet.

ABA383

iTrader: (1)

I used Comp Hi-Tech stainless 1.6s...went 15 years and 54,000 miles before I had them rebuilt by comp for $8.95/each. Very durable, lightweight rocker. Not cheap, however...

--Alan

l 95 Trans Am l

iTrader: (5)

Thats my main issue, I dont have $300 to spend on Rocker arms. How are Scorpions?

defaultexistence

iTrader: (11)

<--Crane golds here..real quiet
here are some budget options.. http://cgi.ebay.com/ebaymotors/ws/eB...K%3AMEWAX%3AIT

Counted Out

iTrader: (6)

I'm going to be putting Scorpion Roller Rockers in my car (they're sitting in my closet). They are a smaller company but all of their stuff is made in the USA. Alot of people on this board have had great luck with them and they are much cheaper than Crane or Comp.

l 95 Trans Am l

iTrader: (5)

Is that legitimate? Only $100?