Street Motor LT1
10-08-2011, 05:25 PM
#41
Launching!
Thread Starter
iTrader: (6)
Join Date: May 2010
Location: Lake Norman, NC
Posts: 286
Likes: 0
Received 0 Likes
on
0 Posts
388 stroker
4 bolt splayed
Wiesco pro tru pistons
6" H beam rods
H series bearings
Arp studs/bolts
LKN speed heads decked .040
Lloyd Elliot 58mm intake
Canton pan
Ford racing 39 lb injectors
1.6 comp roller rockers
Beehive springs
Long tubes
Spec 4 clutch
Deleted a/c and abs
236/242-112 sb circle cam
CSR electric water pump
Double roller timing set
Msd opti
SLP exahust
Full tank of 100 octane lol
Let me know what I missed
Thanks guys
4 bolt splayed
Wiesco pro tru pistons
6" H beam rods
H series bearings
Arp studs/bolts
LKN speed heads decked .040
Lloyd Elliot 58mm intake
Canton pan
Ford racing 39 lb injectors
1.6 comp roller rockers
Beehive springs
Long tubes
Spec 4 clutch
Deleted a/c and abs
236/242-112 sb circle cam
CSR electric water pump
Double roller timing set
Msd opti
SLP exahust
Full tank of 100 octane lol
Let me know what I missed
Thanks guys
10-10-2011, 07:07 PM
#50
Launching!
Thread Starter
iTrader: (6)
Join Date: May 2010
Location: Lake Norman, NC
Posts: 286
Likes: 0
Received 0 Likes
on
0 Posts
It might be closer to 13:1. It may not be necessary but building it probably wasn't necessary either lol
What specs do you need to dial inthe compression? Maybe we can figure it out.
Thanks
What specs do you need to dial inthe compression? Maybe we can figure it out.
Thanks
10-10-2011, 07:29 PM
#52
You don't know what your compression ratio is when your build is complete and the engine is running? 
http://www.turbofast.com.au/Tfcomp.html
http://www.turbofast.com.au/Tfcomp.html
10-29-2011, 06:44 PM
#57
Only have 30 miles on new engine. Too soon for dyno? Been tryin to put more miles on the engine, get the new engine broken in but this bad weather has been a problem and I've only logged on 30 miles so far.
It's been heat cycled and the 2nd oil change as been done but is it too soon for the dyno session on Monday? I forgot to ask Brain from Kaltech about this.
It's been heat cycled and the 2nd oil change as been done but is it too soon for the dyno session on Monday? I forgot to ask Brain from Kaltech about this.
10-29-2011, 07:05 PM
#58
Launching!
Thread Starter
iTrader: (6)
Join Date: May 2010
Location: Lake Norman, NC
Posts: 286
Likes: 0
Received 0 Likes
on
0 Posts
I did 200 miles. I was comftorble with that cause I didn't see smoke. Figured the rings were seated and good to give it hell. That's what it's made for lol
10-29-2011, 07:31 PM
#59
Been tryin to put more miles on the engine, get the new engine broken in but this bad weather has been a problem and I've only logged on 30 miles so far.
It's been heat cycled and the 2nd oil change as been done but is it too soon for the dyno session on Monday? I forgot to ask Brain from Kaltech about this.
It's been heat cycled and the 2nd oil change as been done but is it too soon for the dyno session on Monday? I forgot to ask Brain from Kaltech about this.
BTW, awesome dyno spilner!
