Cleanest LT1
#22
Thread Starter
TECH Fanatic
iTrader: (10)
Joined: May 2005
Posts: 1,197
Likes: 0
From: Charlotte, NC
Originally Posted by ShadyPhi
where are the fuel lines? Thats the big black line that goes over the driver side strut tower
Heck, where is the PCM at? Thats amazing if he hid all that stuff
Heck, where is the PCM at? Thats amazing if he hid all that stuff
#25
Thread Starter
TECH Fanatic
iTrader: (10)
Joined: May 2005
Posts: 1,197
Likes: 0
From: Charlotte, NC
It is hard to keep it clean, but it is doable and he does. Rhis isnt a trailer queen, it can be daily driven, just a lot of effort has been put into it, it was going to be driven down to Atlanta for G10 but it had a bad electric water pump so that kept it from making it down there. These pics were taken while the car was still on the lift and the owner cleaning the bottom. Hopefully we will get some track times in the near future.
#26
Thread Starter
TECH Fanatic
iTrader: (10)
Joined: May 2005
Posts: 1,197
Likes: 0
From: Charlotte, NC
All work was done at F-Body Motorsports, we will have a page dedicated to this car in the near future. In the mean time you can visit our site at fbodymotorsports.com and see all of our project cars, just go to the photo gallery tab and you can check them out there.
#32
all that work with stock valve covers? come on now get some nice chrome ones or some powder coated black ones with bow ties at least. but that **** is clean, i think i just found my project for the rest of the summer.
#35
take a look at my engine bay. Page 4. There are 2 pics there but not up close. I get it back from paint tomorrow. So I will get more pics out soon.
We actually went all the way and welded up some plates over the hole where the fuel lines came in. Also welded up the lines as you can see. we will also be hiding the wires as much as possible
http://www.cardomain.com/ride/2159975/4
We actually went all the way and welded up some plates over the hole where the fuel lines came in. Also welded up the lines as you can see. we will also be hiding the wires as much as possible
http://www.cardomain.com/ride/2159975/4
#36
Thread Starter
TECH Fanatic
iTrader: (10)
Joined: May 2005
Posts: 1,197
Likes: 0
From: Charlotte, NC
Originally Posted by asudecat
take a look at my engine bay. Page 4. There are 2 pics there but not up close. I get it back from paint tomorrow. So I will get more pics out soon.
We actually went all the way and welded up some plates over the hole where the fuel lines came in. Also welded up the lines as you can see. we will also be hiding the wires as much as possible
http://www.cardomain.com/ride/2159975/4
We actually went all the way and welded up some plates over the hole where the fuel lines came in. Also welded up the lines as you can see. we will also be hiding the wires as much as possible
http://www.cardomain.com/ride/2159975/4
#37
heres a pic my bro took..its kinda fusy because its a pic from a phone
http://pictures.sprintpcs.com/mmps/R...,255,1,0,0,0,0
http://pictures.sprintpcs.com/mmps/R...,255,1,0,0,0,0
#38
Took a couple more pics this morning. The car will be done later on today.
Just another close up on the engine bay.
http://www.cardomain.com/ride/2159975/5
Just another close up on the engine bay.
http://www.cardomain.com/ride/2159975/5