Weld wheels
15 x 3.5 = 1.5
15 x 8 = 5.5
15 x 10 = 7.5
Those are the normal 4th gen drag wheel offsets, using those will keep your car from looking redneck with your wheels sticking 6ft out the side of your fender.
Tony.
15 x 8 = 5.5
15 x 10 = 7.5
Those are the normal 4th gen drag wheel offsets, using those will keep your car from looking redneck with your wheels sticking 6ft out the side of your fender.
Tony.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
Originally Posted by the_merv
Cool. What size is the MT ET Street's on there, and how much did you have to modify on the inner body there?
Tony.
Is 11.5 the tread width or section width? Did you have to do any hammering or bending for clearance? I am looking to run a 325/50-15 which is a 28" tire with an 11" tread with and 13" section width. I know a 15x10 with 7.5" backspacing would work good on this but I am trying to figure out how a 6.5" backspacing would look and work.
Originally Posted by DroppedM6Z
They make a 15x10 with 6.5" BS that looks alittle better than the 7.5 if you ask me. I've got a set on mine with the 2" drop and they clear everywhere. Nothing touches at launch.
Originally Posted by fergymoto
Is 11.5 the tread width or section width? Did you have to do any hammering or bending for clearance? I am looking to run a 325/50-15 which is a 28" tire with an 11" tread with and 13" section width. I know a 15x10 with 7.5" backspacing would work good on this but I am trying to figure out how a 6.5" backspacing would look and work.
I think 11.5 was the section....The 13" section is going to require more than a hammer I was under the impression that the 50 was a 26 and the 60 was a 28, am i wrong?
Here is a good setup from what you guys have been sayin..
http://store.summitracing.com/partde...5&autoview=sku
http://store.summitracing.com/partde...5&autoview=sku
http://store.summitracing.com/partde...5&autoview=sku
http://store.summitracing.com/partde...5&autoview=sku
http://store.summitracing.com/partde...5&autoview=sku
http://store.summitracing.com/partde...5&autoview=sku
^Those are the tires I have been planning on. I will probably get Draglites, they look good on both TAs and Camaros. I think maybe slightly more so than Pro Stars. 15x10, was sure on 7.5 backspacing but now I was to see what 6.5 would look like.