input shaft broke
input shaft broke to make a long story short, i was about to streetrace of the line did a burn out, tires didnt spin all you smelled was the clutch but since it was a 2nd burnout I though, what the hell they should be sticky lol. anways raised the rpms waiting for the guy who was flaging and the hands went down punched and the only thing I heard was a loud sound like something broke. Ofcourse it was the clutch b/c the car was still on but wouldnt go no where. Next day started with the removal of the tranny and ofcourse 1st you need to take off the driveshaft. well the **** didnt want to come off. Ok.. Didnt understand why, anyways finaly got fed up pulled it hard of and damn the shaft in the back of the tranny all of a sudden was loose.(inupt shaft) wtf.. you could actually move it around. Anyways yeah my mcleod twin disk was in pieces.
ok this tranny was recently build by a friend of a friend ( i know doesnt sound good right of the bat) well anyways he has rebuild a couple of guys t56 but i bought all new syncroz and goodies and even a new input shaft.. this **** seriously doesnt even have 1K miles on it. anybody ever heard about this happening? the tranny felt good compared to before but **** come on it close me like $500 for the shaft and piece of grad took a **** on the second launch.. just doesnt seem right.. let me know what you guys think. thnx
ok this tranny was recently build by a friend of a friend ( i know doesnt sound good right of the bat) well anyways he has rebuild a couple of guys t56 but i bought all new syncroz and goodies and even a new input shaft.. this **** seriously doesnt even have 1K miles on it. anybody ever heard about this happening? the tranny felt good compared to before but **** come on it close me like $500 for the shaft and piece of grad took a **** on the second launch.. just doesnt seem right.. let me know what you guys think. thnx
Last edited by pewter 01 SS; Feb 8, 2007 at 11:49 AM.
Originally Posted by flash12t
lol not to be a jack *** but **** it was hard to read this. . .hahaha carry on.. i would say call who ever sold u the rebuild kit. . and ya pics please
my bad my bad. see what happens when your at work trying to type fast w/o getting caught by the boss lol..
i should of taken pix before i took it back..
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Originally Posted by Ls1Joe
That is the ouput shaft. I have twisted mine but never broke it.
never seen nor never had it happen either. yeah the output shaft.
and i thought after the money i spend on it, it wouldnt break 
They will bend /warp if the rear end lets go(output shafts). The impact to the whole drivetrain is tremendous.
Fcars actually have a small cross-section spline( I can never remeber if its 27 or 28T). There are other model shafts that significantly beef-up the output. An SSR shaft will most difficult to break( 32 T) and the Fcar trans can be modified to accept it( requires a larger bushing and a yoke change).
Fcars actually have a small cross-section spline( I can never remeber if its 27 or 28T). There are other model shafts that significantly beef-up the output. An SSR shaft will most difficult to break( 32 T) and the Fcar trans can be modified to accept it( requires a larger bushing and a yoke change).
