2 C5 Z06's vs 03 Cobra, Rolls and dig races
#1
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Nov 2001
Location: Las Vegas, NV
Posts: 687
Likes: 0
Received 0 Likes
on
0 Posts
2 C5 Z06's vs 03 Cobra, Rolls and dig races
Here are some runs between 2 C5 Z06's and a 03 Cobra. Enjoy
http://www.youtube.com/watch?v=hEhkbRupeSA
http://www.youtube.com/watch?v=WSkPIm6Phm4
http://www.youtube.com/watch?v=H1f9X31rpSE
http://www.youtube.com/watch?v=FS0CApoIlbc
http://www.youtube.com/watch?v=RcCiJZIsgIc
http://www.youtube.com/watch?v=i4qiR4U1WlY
http://www.youtube.com/watch?v=EnaWpRV6u8k
http://www.youtube.com/watch?v=hfr7Uzo8ZFo
Fun runs.
http://www.youtube.com/watch?v=hEhkbRupeSA
http://www.youtube.com/watch?v=WSkPIm6Phm4
http://www.youtube.com/watch?v=H1f9X31rpSE
http://www.youtube.com/watch?v=FS0CApoIlbc
http://www.youtube.com/watch?v=RcCiJZIsgIc
http://www.youtube.com/watch?v=i4qiR4U1WlY
http://www.youtube.com/watch?v=EnaWpRV6u8k
http://www.youtube.com/watch?v=hfr7Uzo8ZFo
Fun runs.
#5
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Nov 2001
Location: Las Vegas, NV
Posts: 687
Likes: 0
Received 0 Likes
on
0 Posts
Cobra was not stock. It has a pulley, off road X, tune, and Nitto NT05 R drag radials. Makes around 420-430 RWHP. Same power level as the Vettes. He drives decent too.
#8
Teching In
Join Date: Oct 2009
Location: Nashville / Indianapolis
Posts: 18
Likes: 0
Received 2 Likes
on
2 Posts
Ehh not necessarily. They make all different sizes and he could have a big pulley on it like a 3.0 or a 2.93. They really need a smaller one like a 2.76 or 2.63 and then add like a 4lb lower and the outcome would be different.
Good runs though and some strong running vette's!
Good runs though and some strong running vette's!
#9
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Nov 2001
Location: Las Vegas, NV
Posts: 687
Likes: 0
Received 0 Likes
on
0 Posts
Well, it had a stock catback which is hurting him from what I am told. It is also hot as hell out here in Vegas. These runs were done in about 97 degree heat at night, which does not help that hot blower.
#10
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Nov 2001
Location: Las Vegas, NV
Posts: 687
Likes: 0
Received 0 Likes
on
0 Posts
Ehh not necessarily. They make all different sizes and he could have a big pulley on it like a 3.0 or a 2.93. They really need a smaller one like a 2.76 or 2.63 and then add like a 4lb lower and the outcome would be different.
Good runs though and some strong running vette's!
Good runs though and some strong running vette's!
He has a 2.76 on it. He is going to get a catback and then a ported eaton and run us again. I will probably bring my car this time though. hehe Nice stang in your sig.
#13
TECH Fanatic
iTrader: (7)
Ehh not necessarily. They make all different sizes and he could have a big pulley on it like a 3.0 or a 2.93. They really need a smaller one like a 2.76 or 2.63 and then add like a 4lb lower and the outcome would be different.
Good runs though and some strong running vette's!
Good runs though and some strong running vette's!
#14
TECH Senior Member
iTrader: (71)
What are the mods on the Zs? Even a half *** H/C setup should destroy a simple pullied Cobra.
I see they are making about the same power.. Should have been 4+ lengths easily unless the Cobra is just that bad *** of a driver and Zs are taking is easy on the shifts (which the yellow on seemed he was).
I agree, they only make 1 pulley size for those Eatons..................
#17
TECH Enthusiast
Thread Starter
iTrader: (3)
Join Date: Nov 2001
Location: Las Vegas, NV
Posts: 687
Likes: 0
Received 0 Likes
on
0 Posts
LMAO... Have you guys not seen many C5Zs run Cobras or something? After seeing the Cobras mods, or lack there of.. I would expect both Zs to be pulling a LOT LOT harder than they would, shouldn't have been a race.
What are the mods on the Zs? Even a half *** H/C setup should destroy a simple pullied Cobra.
I see they are making about the same power.. Should have been 4+ lengths easily unless the Cobra is just that bad *** of a driver and Zs are taking is easy on the shifts (which the yellow on seemed he was).
Must be a hell of a driver.
I agree, they only make 1 pulley size for those Eatons..................
What are the mods on the Zs? Even a half *** H/C setup should destroy a simple pullied Cobra.
I see they are making about the same power.. Should have been 4+ lengths easily unless the Cobra is just that bad *** of a driver and Zs are taking is easy on the shifts (which the yellow on seemed he was).
Must be a hell of a driver.
I agree, they only make 1 pulley size for those Eatons..................