Livernois LSX Kenne Bell 3.6 LC 2010 Camaro Build
07-28-2010, 04:40 PM
#1
Livernois LSX Kenne Bell 3.6 LC 2010 Camaro Build This car was one of the earlier L99 build's we did in 2009.
Mod's were as follows:
The car went 11.02 @ 126 mph with Andy@Livernois behind the wheel and was the runner up at the LSX Shootout last year.
The customer decided he needed more power, so the car will be going back under the knife shorty for the following mods.
Here are a few photos of some of the parts
Huge Inlet! (Pop can used for reference of size)
I will update this thread as the build progresses.
Thanks for looking!
Regards,
Rick LeBlanc
Livernois Motorsports
Mod's were as follows:
- Magnacharger MP2300 Intercooled Supercharger
- Livernois Motorsports Ported Lower Supercharger Manifold
- Livernois Motorsports CNC Ported Cylinder Heads
- Livernois Motorsports DOD/VCT Delete Kit
- Livernois Motorsports L92 Stage 1B Camshaft
- 60# Injectors
- Kenne Bell Boost-A-Pump
- Kooks 1 7/8” Longtube Headers
- Kooks Catted Connection Pipe
- Corsa Catback
- Rotofab Cold Air Intake
- Nitto 275/40/20 Drag Radials
- Tuned by Livernois Motorsports
The car went 11.02 @ 126 mph with Andy@Livernois behind the wheel and was the runner up at the LSX Shootout last year.
The customer decided he needed more power, so the car will be going back under the knife shorty for the following mods.
- Livernois Built 440ci Stroker Longblock
- GM LSX Block
- Livernois Spec Forged Crankshaft
- Livernois Spec Carrillo Forged Pro H-Beam Rods
- Livernois Spec Forged/Coated Pistons
- Livernois Spec Custom Camshaft
- Coated Bearings
- Billet Timing Chain Set
- All ARP 2000 Hardware
- Livernois CNC Ported GM LSX DR Cylinder Heads
- Kenne Bell 3.6L Liquid Cooled S/C
- Livernois Custom 10-Rib Setup
- Livernois Custom Fuel System
- Fully Built A6 Automatic Transmission
- TCI Flexplate
- Hendrix 9-Inch w/ Upgraded Axles & Driveshaft
- Metco Driveshaft Loop
- Pfadt Drag Springs
- Pfadt Drag Swaybar
- BMR Trailing Arms
- BMR Toe Rods
- BMR Subframe Connectors
- Cowl Hood Painted by Livernois Motorsports
Here are a few photos of some of the parts
Huge Inlet! (Pop can used for reference of size)
I will update this thread as the build progresses.
Thanks for looking!
Regards,
Rick LeBlanc
Livernois Motorsports
07-28-2010, 04:58 PM
#3
07-28-2010, 05:08 PM
#4
TECH Regular
iTrader: (38)
Join Date: Sep 2008
Location: edmond, ok
Posts: 498
Likes: 0
Received 0 Likes
on
0 Posts
Thank you!
We can't wait either, however it will be a while before complete as we are still waiting for parts.
We have another (that looks like its twin) however that should be ready by the end of this week/early next week.
See this thread.
-Rick
We can't wait either, however it will be a while before complete as we are still waiting for parts.
We have another (that looks like its twin) however that should be ready by the end of this week/early next week.
See this thread.
-Rick
07-31-2010, 06:49 PM
#6
Administrator
I can't believe how big that blower is in real life (as opposed to internet pics). It absolutely dwarfs my baby 2.2L KB. It's a monster. This is going to be one badass car Rick. 
