skeeter99

iTrader: (16)

Lmfao!!! yep just like that on a lil stub still bolted to tail shaft the rest where just splintered

green94z

iTrader: (6)

Was he at redline last nite?

skeeter99

iTrader: (16)

Yep next to u when it happened, we need to get a drive shaft from u

green94z

iTrader: (6)

Your kidding right? After you ripped off Jerry. No we're not dealing with crooks. Btw my car 200 off the line no problems!

skeeter99

iTrader: (16)

Thats was just leaving off the trans brake he didnt hit the spray yet. And if u have a 12 bolt as your sig says then i would hope it would hold. Any how he will take his money somewhere else no prob. Next time he is out there you should run him.

green94z

iTrader: (6)

Ya it has a 12 bolt, we gota move 300+ pounds more then you. Stock drive shaft. We will run him any time he wants to get his *** drug

Btw weve been 1.3x 60' on a 10 bolt at 3400ish pounds.

skeeter99

iTrader: (16)

That's cool he weighed i'n at 2700ish after two stock seats and some more stuff added I didn't have i'n there well be at k Dale Friday

SSHAWK

iTrader: (14)

I’ve seen Daniels brother car run and it does move” Bad little car for what it has done” .. As for Josh’s car that bitches light as hell …I still think he could shave some more weight if he wanted to go that route. But…. what it all comes down to is making it down the track in one piece.. And I haven’t seen it make a real pass yet.. Not saying it won’t just hasn’t done one yet.

I will say this though, if he does get the bugs worked out of his car that cars going to be one hard car to beat…

BSmiff

Im not surprised the stock driveshaft broke before the rear but once that 12 bolt is in and a nice steel driveshaft its going to roll. As far Daniel's brothers car, that **** is a beast at full weight. Not sure if its street driven anymore but when it had the 4l60e it had to be one of the better sleepers in Dallas.

skeeter99

iTrader: (16)

Yea i have heard it runs 6.40's or so which is awesome. I think he has a fooger on it with a stand alone if its the same system daniel use to run. Any how my car is dead hooking now which is good, but bad for the 10 bolt. If the rear last a few passes it will make a good number. I was told my car would never run a 10.xx on motor by daniel although it ran a 6.9x on motor at k dale not sure what that is in 1/4. But the car was different than. All's i can say is well see. 2700 pounds and 600ish on spray it better do something

green94z

iTrader: (6)

My car never ran 6.4s. My car is slow. Daniel never had a fogger on his car. My car is still street driven, not as much as I would like to. My work schedule wont allow me to bring it out friday, but we will be out saturday. Your car will be fast @2700 and 600hp

ProTreeRacing

iTrader: (4)

Lemme correct u...i told u wat your car would run and it ran that exact number...a 6.9 would b an extremely low 11...maybe high 10...the grn car is only missin ac/heat...id jump in it n drive to mexico no hesitation...also dead hooking is way better then not...at that power and weight you should be low low 9s or high 8....just for kicks what does it 60 on motor and wat gears?

SSHAWK

iTrader: (14)

From what I was told he did 1.5 60ft .... 373 gears.

He thinks his car weighs 2700... Im going with 2900.. 2950 lbs.. He's put **** back in the car that doesn't need to be in the car.

Your cars not slow your just dialing it in lol

ProTreeRacing

iTrader: (4)

If the car hooks or wheel hops it will strip the teeth off the ring gear I bet...and r we talkin with a driver or without? He added 200 pounds? Thats a lot

skeeter99

iTrader: (16)

my lt1 car weighed like 2950 with haeavy *** zr1's and this car has waaayyyy more **** taken out, full chromoloy k member and upper/lower arms, the th350 and 8 inch converter, he did put a fiberglass hood but its as heavy as the stock ss hood was imo cuz its a bolt on hood, i have him talked into lettting me take more weight out now like i want, only thing that sucks now is the heavy hood the vfn i wanted was 14 pounds and u delete the hinges ect... so big weight lose. Were going to cut out the t top hump, and both wells and i got some more ideas. he added the nitrous stuff after it was weighed and this weight was with both stock seats and we got a kirkey that will go in on race day. He just likes the stock look better than me. this was w/o him so 2900ish race weight

SSHAWK

iTrader: (14)

Like I said above 2900.... I don't care what the car weighs without him in it I'm not racing a empty car lol

But knowing you ...I bet you have a **** ton of stuff about to be removed out of this car lol

Make sure to take a video of the first pass.... Ask him to let you run it first and Tell him you will do a run like I did so you don't break the rearend on the first pass.

Then at the end of the night if he wants to try his way he can have at it.

skeeter99

iTrader: (16)

If we strip the 3.73 well try some 3.42 and weld the axle tubes up but at the end of the day its still a weak 10 bolt and i cant get that in his head. Even John ferry told him not to leave on it all so he may listen to them.

SSHAWK

iTrader: (14)

I might be going to Redline tonight one of my Friends is running his car... Tell Jason to go to Redline... Kdale is so damn far for me .

Tell him I will video his runs for him.

SSHAWK

iTrader: (14)

Well it was a good run

ProTreeRacing....... Racing green94z car vs Skeeter99 SS

Both will be posting up videos of the runs.

Both cars wheels came up..

In the end green94z car won... His car did very well.

Skeeter99's car ran very well for what it has.

ProTreeRacing

iTrader: (4)

Our video is bad for some reason...it figures...i hope skeeter has it...our video shows the driver front wheel still up 30 feet out...was a good night...glad we could help you guy with the overflow and tire pressure to make the car work...it will fly with the bugs worked out...just stick with it