TNT Kit and Lid Fitment
TNT Kit and Lid Fitment I have a SLP Lid and fact. bellow.
I've done tons of searching and its seems its the WS6 owners who have the most fitments issues, due to the higher air box.
I'm now going to have to order another lid. I progressively trimmed the lid down and even now it barely fits. I had to move the sensor back too. You can see the hole where the sensor originally was.....
The next lid I think I will cut at an angle,
If there are any WS6 owners that have helpful info i'd greatly appreciate it.
If anyone with a WS6 has any advice please feel free to chime in.
I've done tons of searching and its seems its the WS6 owners who have the most fitments issues, due to the higher air box.
I'm now going to have to order another lid. I progressively trimmed the lid down and even now it barely fits. I had to move the sensor back too. You can see the hole where the sensor originally was.....
The next lid I think I will cut at an angle,
If there are any WS6 owners that have helpful info i'd greatly appreciate it.
If anyone with a WS6 has any advice please feel free to chime in.
well i've got another lid i'm gonna get for cheap, now i'm researching bellows. I hate to pay $50-$60 for a piece of rubber, but i dont think a Fernco from HomeDepot will have enough bend in it.
I dont like SLP's b/c its just a big bubble, but i have looked at MTI's and its got a nice angle to it.
I dont like SLP's b/c its just a big bubble, but i have looked at MTI's and its got a nice angle to it.
Last edited by jaypee1217; Feb 2, 2005 at 11:21 PM.
I used a fernco hose and removed about 1.5" from the Lid- These pics aren't the best, but I'll be monkeying with it some today and I'll take a few better ones for you. I'd suggest using the fernco hoses because if you screw one up, it's not a lot of $$$ to throw in the trash.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
TECH Apprentice
Joined: Jul 2004
Posts: 304
Likes: 0
From: Texas
Originally Posted by jaypee1217
I have a SLP Lid and fact. bellow.
I've done tons of searching and its seems its the WS6 owners who have the most fitments issues, due to the higher air box.
I'm now going to have to order another lid. I progressively trimmed the lid down and even now it barely fits. I had to move the sensor back too. You can see the hole where the sensor originally was.....
The next lid I think I will cut at an angle,
If there are any WS6 owners that have helpful info i'd greatly appreciate it.
If anyone with a WS6 has any advice please feel free to chime in.
I've done tons of searching and its seems its the WS6 owners who have the most fitments issues, due to the higher air box.
I'm now going to have to order another lid. I progressively trimmed the lid down and even now it barely fits. I had to move the sensor back too. You can see the hole where the sensor originally was.....
The next lid I think I will cut at an angle,
If there are any WS6 owners that have helpful info i'd greatly appreciate it.
If anyone with a WS6 has any advice please feel free to chime in.
You didnt get excited with the trim part did ya? There is only so much that can be taken off.. Was the MAF comming in contact with the PR?
TECH Apprentice
Joined: Jul 2004
Posts: 304
Likes: 0
From: Texas
Originally Posted by 02 WS6 TA
Here are a few more, hope they help. 
Your install turned out pretty clean, I see that you had to twist the bracket 4 the pressure gauge, but am curious as to why you have the pressure gauge by the sol?? BTW Nice job on the intake!!
David, I had to twist the bracket because of the WOT switch/Linkage/Cable location, made more difficult by the BBK TB and spacer. The Pressure gauge there was to call bluff on the Bottle mounted gauge in the rear- We had a delivery problem we were chasing. 
TECH Apprentice
Joined: Jul 2004
Posts: 304
Likes: 0
From: Texas
Originally Posted by 02 WS6 TA
David, I had to twist the bracket because of the WOT switch/Linkage/Cable location, made more difficult by the BBK TB and spacer. The Pressure gauge there was to call bluff on the Bottle mounted gauge in the rear- We had a delivery problem we were chasing.
I want this New Bracket...
Originally Posted by David@TNT
Thats cool, was just curious.. Our new backet has the WOT switch mounted on it..
Originally Posted by David@TNT
You didnt get excited with the trim part did ya? There is only so much that can be taken off.. Was the MAF comming in contact with the PR?
