Nitrous Oxide Installation | Tuning | Products
Sponsored by:
Sponsored by:

Nx Maf -dual Feed Single Stage

Thread Tools
 
Search this Thread
 
Old Feb 24, 2006 | 11:04 PM
  #1  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default Nx Maf -dual Feed Single Stage

I wonder if any one has used the NX MAF (w/o integrated solenoids) with both N20 lines and both fuel line T'd off single solenoids in a single stage setup. In other words have single outlets from the nitrous and fuel solenoids going to T fittings and off to the 2 inlets on the MAF housuing on each side? In a similar fashion as the TNT F1 kit(?). For a 150 shot the jets would be 2 x 75 shot for each nozzle. Any reason NOT to experiment with this setup?
Reply
Old Feb 24, 2006 | 11:09 PM
  #2  
Robert56's Avatar
TECH Senior Member
iTrader: (2)
 
Joined: Aug 2003
Posts: 9,557
Likes: 1
From: Tacoma, WA
Default

I am not a NX expert, but sounds like it should work fine. Similar to a lot of the wet dual nozzle kits. As long as your noids are big enough, as some of the noids on the maf kits use the smaller noids.
Robert
Reply
Old Feb 24, 2006 | 11:11 PM
  #3  
NXRICKY's Avatar
Closed ex-Sponsor Account
iTrader: (1)
 
Joined: Jul 2004
Posts: 2,797
Likes: 0
From: Wichita Falls, TX
Default

Originally Posted by Macon
I wonder if any one has used the NX MAF (w/o integrated solenoids) with both N20 lines and both fuel line T'd off single solenoids in a single stage setup. In other words have single outlets from the nitrous and fuel solenoids going to T fittings and off to the 2 inlets on the MAF housuing on each side? In a similar fashion as the TNT F1 kit(?). For a 150 shot the jets would be 2 x 75 shot for each nozzle. Any reason NOT to experiment with this setup?
150 is 150. The Maf will work as a twin nozzle set up.

Ricky
Reply
Old Feb 25, 2006 | 07:48 AM
  #4  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default

Originally Posted by NXRICKY
150 is 150. The Maf will work as a twin nozzle set up.

Ricky
So no advantages to doing it? Disadvantage would be more plumbing.
Reply
Old Feb 25, 2006 | 12:31 PM
  #5  
NXRICKY's Avatar
Closed ex-Sponsor Account
iTrader: (1)
 
Joined: Jul 2004
Posts: 2,797
Likes: 0
From: Wichita Falls, TX
Default

Yeppers.
Ricky
Reply
Old Feb 25, 2006 | 01:12 PM
  #6  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default

Originally Posted by NXRICKY
Yeppers.
Ricky
Thanks !!
Reply
Old Feb 25, 2006 | 01:15 PM
  #7  
NXRICKY's Avatar
Closed ex-Sponsor Account
iTrader: (1)
 
Joined: Jul 2004
Posts: 2,797
Likes: 0
From: Wichita Falls, TX
Default

As always Mr. Macon you are welcome. So whens the new dynoing happening.?
Ricky
Reply
Old Feb 25, 2006 | 03:49 PM
  #8  
Robert56's Avatar
TECH Senior Member
iTrader: (2)
 
Joined: Aug 2003
Posts: 9,557
Likes: 1
From: Tacoma, WA
Default

C'mon, Macon, quite being a wuss. A couple more noids, a controller and 150 to each side and bingo a dual stager.
Robert
Reply
Old Feb 25, 2006 | 09:35 PM
  #9  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default

Originally Posted by NXRICKY
As always Mr. Macon you are welcome. So whens the new dynoing happening.?
Ricky
Thank you...all this was from a simple thought that maybe spreading out the spray might yield some interesting results. I'm glad to be continuing to learn at a rapid pace and enjoy the fact that I can ask lots of questions. The next dyno runs come in March with the stand alone system....yes Robert I can do comparitive analysis, and with my DynoJets software. Someday i'll be as good as you!

Oh yea...what a Mullet?

Last edited by Macon; Feb 25, 2006 at 09:51 PM.
Reply
Old Feb 25, 2006 | 09:50 PM
  #10  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default

Originally Posted by Robert56
C'mon, Macon, quite being a wuss. A couple more noids, a controller and 150 to each side and bingo a dual stager.
Robert
I didn't notice that one...my plans are much more lofty than that.
Reply
Old Feb 25, 2006 | 11:47 PM
  #11  
Robert56's Avatar
TECH Senior Member
iTrader: (2)
 
Joined: Aug 2003
Posts: 9,557
Likes: 1
From: Tacoma, WA
Default

Originally Posted by Macon
I didn't notice that one...my plans are much more lofty than that.
Cool, sorry I pissed you off Macon, wasn't my intent.
Robert
Reply
Old Feb 26, 2006 | 09:22 AM
  #12  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default

Originally Posted by Robert56
Cool, sorry I pissed you off Macon, wasn't my intent.
Robert
Robert I want to belive that it is infrequesnt that people TRY to **** people off here but they do any way. When that happens I back off and remember why I poke my head in here...it's a free education on things concerning the car when we get lucky.
Reply
Old Feb 26, 2006 | 09:47 AM
  #13  
227Hawk's Avatar
TECH Fanatic
iTrader: (1)
 
Joined: Nov 2001
Posts: 1,735
Likes: 0
From: Turlock, Ca
Default

Originally Posted by Macon
my plans are much more lofty than that.
Care to give us a hint?????????
Hawk
Reply
Old Feb 26, 2006 | 11:37 AM
  #14  
BadAssFast's Avatar
Thread Starter
10 Second Club
iTrader: (2)
 
Joined: Dec 2004
Posts: 1,386
Likes: 1
From: Sumter, South Carolina
Default

Originally Posted by 227Hawk
Care to give us a hint?????????
Hawk
Soon...soon...I'm a show off. Now if I can get my car to look as clean as yours!!
Reply
Old Feb 26, 2006 | 05:37 PM
  #15  
227Hawk's Avatar
TECH Fanatic
iTrader: (1)
 
Joined: Nov 2001
Posts: 1,735
Likes: 0
From: Turlock, Ca
Default

Originally Posted by Macon
Soon...soon...I'm a show off. Now if I can get my car to look as clean as yours!!
I don't know how clean but it's going to be different.

Teasers soon to follow on 3rd stage.
Hawk
Reply




All times are GMT -5. The time now is 11:40 AM.