help with dynotune ws
help with dynotune ws ok I hooked up everything. how do i test it? do I have to program it? I tried turing the key on and pushing the pedal to the floor to see if the noids would click and got nothing. not sure what to do next.
not to be sarcastic, but did you read the directions?
http://www.dynotunenitrous.com/store...W%20SWITCH.pdf
http://www.dynotunenitrous.com/store...W%20SWITCH.pdf
Last edited by 860 Performance; Mar 25, 2008 at 05:22 AM.
TECH Fanatic
Joined: Nov 2001
Posts: 1,064
Likes: 0
From: CA
not to be sarcastic, but did you read the directions?
http://www.dynotunenitrous.com/store...W%20SWITCH.pdf
http://www.dynotunenitrous.com/store...W%20SWITCH.pdf
seriously, 890 perf GAVE YOU the answer
maybe I can't read....but where does it say how to test it? I followed the instructions for #8 but got nothing. since I am not hering the click do I have something wrong?
you probably hooked it up right. however being that its rpm activated, it wont activate a solenoid when your car is not running....which im assuming it wasnt. unless you have REALLY quiet exhaust such that you could hear a solenoid. when i did mine (dry kit) i just taped my feed like to the cowl so i could see it and gave her a rev. saw nitrous right at 3000 RPM so i was good!
when i did mine (dry kit) i just taped my feed like to the cowl so i could see it and gave her a rev. saw nitrous right at 3000 RPM so i was good! Trending Topics
you probably hooked it up right. however being that its rpm activated, it wont activate a solenoid when your car is not running....which im assuming it wasnt. unless you have REALLY quiet exhaust such that you could hear a solenoid. when i did mine (dry kit) i just taped my feed like to the cowl so i could see it and gave her a rev. saw nitrous right at 3000 RPM so i was good!
when i did mine (dry kit) i just taped my feed like to the cowl so i could see it and gave her a rev. saw nitrous right at 3000 RPM so i was good!LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo
i really don't like going wot to test the solenoids.
you'd have to rig it up to test it. check with dynotune but "i think" you could feed the wotwire(blue) with a 12 volt to activate the wot. then rev to 3000 or whatever you have set for activation.
you'd have to rig it up to test it. check with dynotune but "i think" you could feed the wotwire(blue) with a 12 volt to activate the wot. then rev to 3000 or whatever you have set for activation.
Teching In
Joined: Jun 2007
Posts: 24
Likes: 0
If all is wired up start the car and push button 1, this will confirm your box is reading the rpm's correctly. Idle up a little say 15-1800. it must match.
IF its good go for a test drive.
Do not put 12volts on the blue wire unless it is set up for 12volt input.
IF its good go for a test drive.
Do not put 12volts on the blue wire unless it is set up for 12volt input.