Ford 9" - 'Quick Performance' Housing
Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
I got some new brake lines bent up and installed. Tried to get the old ones to work, and they would have "worked", but they looked like **** so I bent up some new ones. Also fabbed up a little aluminum bracket to hold the Tee fitting in place. Pics to come shortly. 
Now the calipers look like hell compared to the rest lol... It's a vicious circle once you make some thing look decent, it tends to make everything around it look crappy haha.... Will it end......?
Mike
Now the calipers look like hell compared to the rest lol... It's a vicious circle once you make some thing look decent, it tends to make everything around it look crappy haha.... Will it end......?
Mike
Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
I finally got around to uploading the install pics from my camera so here's some more.....
This is a bracket I fabbed up for the Tee fitting for the brakes.
I bent up some new hard lines for the brakes. The stock ones were pretty ragged looking. What can I say, I'm kinda picky.
The Strange 'S' Case with the final gear settings and billet yoke installed.
Adjusting the panhard rod for the side-to-side clearance for the 315's.
That's it for now.
Mike
This is a bracket I fabbed up for the Tee fitting for the brakes.
I bent up some new hard lines for the brakes. The stock ones were pretty ragged looking. What can I say, I'm kinda picky.
The Strange 'S' Case with the final gear settings and billet yoke installed.
Adjusting the panhard rod for the side-to-side clearance for the 315's.
That's it for now.
Mike
Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
Thanks man. I am getting really antsy to drive the car again. I mean REALLY bad lol..... After some major setbacks, it's finally going to be back in business. Can't wait to roll with you guys this summer. 
Mike
Mike
I can see those front tires coming of the ground with no trouble..Very nice Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
(well of course the rear end and gears) LS1 Tech Stories
The Best V8 Stories One Small Block at Time
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
Awesome K5 Blazer Restomod Comes With C7 Corvette Power
Verdad Gallardo
10 Camaros You Should Never Buy
10 LS Engine Myths That Refuse to Die
Verdad Gallardo Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
Mike
Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
Mike
Just bought my 35 spline detroit locker yesterday and won the bid on some gears today, and I am talking with the guy I won the gears from about bumping down the shipping a little if I buy a pinion yoke from him. I am pretty sure I am going with the QP housing and they have a pretty good deal on an S-case with pinion support and bearings
Thread Starter
11 Second Club
iTrader: (37)
Joined: Mar 2004
Posts: 2,046
Likes: 3
From: Vancouver, WA
Just bought my 35 spline detroit locker yesterday and won the bid on some gears today, and I am talking with the guy I won the gears from about bumping down the shipping a little if I buy a pinion yoke from him. I am pretty sure I am going with the QP housing and they have a pretty good deal on an S-case with pinion support and bearings
The S Case is a good piece from what I've heard. Should reliably hold up to 800hp with no issues.
Mike
