Big Turbo Car Part Out...
#1
On The Tree
Thread Starter
iTrader: (24)
Join Date: Dec 2006
Location: Arkansas
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Big Turbo Car Part Out...
Category: Audio/Video/Electronics
Price: $0
Part Fits: 93-02 Chevrolet Camaro
Location (State): VA
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS1/LS6
Motor: LME LS3 416ci
SHORTBLOCK:L92 416 cid. balanced, blueprinted & assembled shortblock:
Callies Compstar 4340 4.0" crankshaft, Callies 6.125" Hbeam rods
w/ ARP 2000 7/16" bolts, Wiseco 4.07" -32cc dish pistons (9.0:1
w/ 66cc chamber), Total seal rings 1/16" 1/16" 3mm, Clevite MS
2199H mains, Clevite CB 663 H rods, Dura Bond CH-23 cam
bearings, ARP main studs.
LS1 cam retainer plate
LS2 block conversion kit: LS2 timing cover w/ cam sensor, lifter
trays, valley cover & cam/ knock sensor extension harness.
Melling 10295 high pressure, coated oil pump/ ported
Roll master double roller timing set w/ torington bearing &
nitrided gears.
GM LS7 hydraulic roller lifters
LS1 Lifter Tray & Bolts
Exotic Performance Blower Camshaft
Cometic Head Gaskets
ARP Head Studs
ATI Balancer
TOP END: AFR 225 72cc Heads, Victor JR EFI Intake, Ultra Low Elbow, Edlebrock 90mm Throttle Body, 96# Injectors
Motor has never been turned over. Only thing that has been used on this Engine is the AFR Heads (ran them for 500 miles before this build). Complete from Throttle Body to Oil Pan. And includes all accessories.
$8,000 really do not want to ship this, but I will drive a reasonable distance to meet someone.
Items Priced to INCLUDE shipping:
SJM ABS Delete w/ Line Lock $140 PENDING
Wolfe Drag Bar BNIB $320
Pavlock Performance LCA's $150
Pavlock Performance PHB $100
BMR Battery Relocation Bracket $70
BMR AC Delete Plate $45
Aeromotive Electric Fuel Pump Controller p/n 16306 $270
Aeromotive Fuel Pressure Regulator p/n 13101 $110 PENDING
Aeromotive Fuel Filters (2) p/n 12304 $80 each PENDING
MSD Tach Signal Driver $45
Items Priced EXCLUDING shipping:
Precision 91.5mm Turbo bought from Wormboy @ LMR. Turbo has 98mm Internals and was used by LMR. I however have never ran it. I will take $1,500
Custom Built Turbo Headers $600 or will sell T6 Flanged Hot Side complete $1,200
QA1 Front "Strut" w/ Springs & Strange Rear Shocks $300 + your stock setup PENDING
Nasty Performance Sumped Fuel Tank $600 PENDING
Griffin Dual Pass Radiator $350
Aeromotive Eliminator Fuel Pump $300 SOLD
It's late, I'm sure I left out a few details here and there. I will gladly answer any questions you may have through PM or through this thread. I plan on getting pictures of everything tomorrow and post them up ASAP. Like I said, I don't need any low ball offers so don't waste your time or mine. Really hate to sell the car but, I need a new C6 in the garage
Blake
Last edited by Blake01SS; 01-05-2010 at 08:18 PM.
#4
On The Tree
Thread Starter
iTrader: (24)
Join Date: Dec 2006
Location: Arkansas
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
itsback08 - I will let the Complete Shortblock go for $6,000 with the Camshaft. This will include all accessories and Head Studs.
99bluehawk - I have a pic on my iPhone I am trying to post up. Give me a few minutes and I should have one. I cant sell the whole Turbo Kit, a good friend has already bought the WG, FMIC, and BOV. I will however let go of the Turbo and Complete Hotside for $2,500.This will include the Brace you will see in the picture to support the Turbo and Core Support. *EDIT* I will be willing to meet you in Longview to avoid shipping hassles.
Blake
99bluehawk - I have a pic on my iPhone I am trying to post up. Give me a few minutes and I should have one. I cant sell the whole Turbo Kit, a good friend has already bought the WG, FMIC, and BOV. I will however let go of the Turbo and Complete Hotside for $2,500.This will include the Brace you will see in the picture to support the Turbo and Core Support. *EDIT* I will be willing to meet you in Longview to avoid shipping hassles.
Blake
Trending Topics
#8
On The Tree
Thread Starter
iTrader: (24)
Join Date: Dec 2006
Location: Arkansas
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Aeromotive Eliminator
Drivers Side Turbo Header and ABS Delete w/ Line Lock
Nasty Performance Sumped Fuel Tank
Turbo and Hot Side w/ Brackets (Wastegate not included)
Engine Shot w/ Turbo Headers
91.5mm Precision Turbo
If you need pics of anything that I wasn't able to take pictures of PM me your email and I will just email you a few. It was cold in the shop with poor lighting so I gave up.
Thanks, Blake
Last edited by Blake01SS; 01-03-2010 at 05:54 PM.
#13
On The Tree
Thread Starter
iTrader: (24)
Join Date: Dec 2006
Location: Arkansas
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
Yes, the headers are mild steel and both have been jet hot coated. I suppose the kit could retain AC but its going to take alot of creativity and skill to make everything work well.
Blake
Blake
#16
pics
this is a link to a few pics I had in my photobucket.
http://s372.photobucket.com/albums/o...20ss%20camaro/
http://s372.photobucket.com/albums/o...20ss%20camaro/
#20
On The Tree
Thread Starter
iTrader: (24)
Join Date: Dec 2006
Location: Arkansas
Posts: 151
Likes: 0
Received 0 Likes
on
0 Posts
I'm trying to keep the motor together for now. If anyone wants the shortblock I will consider separating it.
Caindo - I believe the fuel pump is already sold locally. I will let you know if the deal falls thru.
Blake
Caindo - I believe the fuel pump is already sold locally. I will let you know if the deal falls thru.
Blake