408 engine in need of overhaul , LS1 water pump, LS1 intake
09-21-2010 | 07:52 PM
#1
Thread Starter
Sawzall and Welder Mod
iTrader: (46)
Joined: Nov 2001
Posts: 2,486
Likes: 4
From: Orlando, FL
408 engine in need of overhaul , LS1 water pump, LS1 intake Category: Engine - Complete Motors
Price: $1000
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird, Corvette, 04-06 Pontiac GTO, 04+ Cadillac CTS-V
Location (State): FL
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS2/LS3/LS7/L92/LS9, LS1/LS6
LS Engine?: Fits LS Engine
2005 block iron 408 stroker short block
Eagle forged 4.0 stroke crank balanced
Eagle H beam forged 6.125 rods
JE forged pistons 4.030 ( small dish, could be either NA or FI depending on heads used)
This was a running engine when it was removed last Friday, but inspection of a main bearing cap shows scoring of the bearings, so it should be overhauled. There are scratches in the bore that may or may not come out with a hone. If they dont come out then youll have to sell these pistons and buy 4.040 size.
-Still assembled-
$1000 takes it as is.
$300 extra and I'll include the 317 heads that came from it with 918 springs and ARP 12 point head studs
LS1 intake $40 plus shipping
Nearly brand new LS1 water pump (less than 1K honest miles before upgraded to EWP) $65 plus shipping
Last edited by Whistler; 09-26-2010 at 02:09 PM.
09-21-2010 | 08:06 PM
#2
Joined: Apr 2004
Posts: 16,776
Likes: 0
From: In a van DOWN BY THE RIVER
2005 block iron 408 stroker short block
Eagle forged 4.0 stroke crank balanced
Eagle H beam forged 6.125 rods
JE forged pistons 4.030 ( small dish, could be either NA or FI depending on heads used)
This was a running engine when it was removed last Friday, but inspection of a main bearing cap shows scoring of the bearings, so it should be overhauled. There are scratches in the bore that may or may not come out with a hone. If they dont come out then youll have to sell these pistons and buy 4.040 size.
-Still assembled-
$1000 takes it as is.
$300 extra and I'll include the 317 heads that came from it with 918 springs and ARP 12 point head studs
LS1 intake $40 plus shipping
Nearly brand new LS1 water pump (less than 1K honest miles before upgraded to EWP) $65 plus shipping
Eagle forged 4.0 stroke crank balanced
Eagle H beam forged 6.125 rods
JE forged pistons 4.030 ( small dish, could be either NA or FI depending on heads used)
This was a running engine when it was removed last Friday, but inspection of a main bearing cap shows scoring of the bearings, so it should be overhauled. There are scratches in the bore that may or may not come out with a hone. If they dont come out then youll have to sell these pistons and buy 4.040 size.
-Still assembled-
$1000 takes it as is.
$300 extra and I'll include the 317 heads that came from it with 918 springs and ARP 12 point head studs
LS1 intake $40 plus shipping
Nearly brand new LS1 water pump (less than 1K honest miles before upgraded to EWP) $65 plus shipping
what dish are the pistons cc's?? 
Trending Topics
09-22-2010 | 05:17 PM
#16
Thread Starter
Sawzall and Welder Mod
iTrader: (46)
Joined: Nov 2001
Posts: 2,486
Likes: 4
From: Orlando, FL
Heres some I just took.
The pistons are JE job #751345
-10cc dish
1.115 compression height
10.1:1 SCR w stock 317 head and head gasket
The pistons are JE job #751345
-10cc dish
1.115 compression height
10.1:1 SCR w stock 317 head and head gasket
Last edited by Whistler; 11-26-2010 at 11:58 PM.
