Moser 9" rear end. Suspension.
#1
TECH Addict
Thread Starter
iTrader: (10)
Join Date: Jul 2006
Location: Wood River, IL
Posts: 2,786
Likes: 0
Received 0 Likes
on
0 Posts
Moser 9" rear end. Suspension.
Category: Drivetrain
Price: $3000
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird
Location (State): IL
Item Condition: Used
LS Engine?: Fits LS Engine
Under 1500 miles on this setup.
35 spline
Wavetrac
3.75 gears
LCA relocation brackets
Adjustable Torque Arm
APR 2.5" long 1/2" studs.
Extra Drain plug
PST 3.5 1000HP rated aluminum drive shaft. Sized for a 6 speed
Powdercoated black
All assembled with backing plates.
This setup runs just over 4k.
Asking 3k plus your 10bolt, torque arm with bushing and drive shaft out of your 6 speed car. Will need your backing plates as you are getting mine. Gears need to be between 3.42s and 4.10s. Rear needs to be assembled already. I will not ship so please don't ask. I can't meet half way either because I don't have a truck.
I can also sell you my On-Car adjustable panhard bar and LCAs. Both powder coated in black. Also the Rear sway bar and the brackets used to hold the sway bar to the rear end. Extra $350 + your stock parts. Will not sell these parts unless you buy the rear end!!
Located in Wood River, IL. Down by St. Louis.
Last edited by BlkBird2000; 06-28-2011 at 07:10 AM.
#5
TECH Addict
Thread Starter
iTrader: (10)
Join Date: Jul 2006
Location: Wood River, IL
Posts: 2,786
Likes: 0
Received 0 Likes
on
0 Posts
This rear end does not have ABS or TCS. I forgot to mention that.
The y pipe consists of a 3-3.5" flowmaster merge and some very nice fabrication buy my local exhaust shop.
The y pipe consists of a 3-3.5" flowmaster merge and some very nice fabrication buy my local exhaust shop.
Trending Topics
#10
TECH Addict
Thread Starter
iTrader: (10)
Join Date: Jul 2006
Location: Wood River, IL
Posts: 2,786
Likes: 0
Received 0 Likes
on
0 Posts
I don't see how I'm high on the price. This rear end starts at $2900 without the $400 torque arm, $400 drive shaft, and without the $200 powdercoating. Also include the extra drain plug and my apr studs. A 10 bolt is worth maybe 200? So your saving 800 on a new moser 9" w/ wavetrac.
There is a very small whine at 45-55mph. You have to be listening for it to hear it. No one else besides me even notices it.
I wanna sell the rear end as a whole set up... rear, ds, tqe arm... just because I don't want left over pieces to try and sell.
There is a very small whine at 45-55mph. You have to be listening for it to hear it. No one else besides me even notices it.
I wanna sell the rear end as a whole set up... rear, ds, tqe arm... just because I don't want left over pieces to try and sell.
#12
On The Tree
iTrader: (4)
Join Date: Aug 2008
Location: IL side of STL
Posts: 125
Likes: 0
Received 0 Likes
on
0 Posts
I am 27 and grew up in wood river and have raced "test n tune" since high school and I'm from alton now but still know who has what in the area besides Alton I have no clue. I only have seen 1 other black car like ours and hes from bethalto, I just took my stock 10 bolt,torsen T2,4.10's,axles out and put in a lower mileage 10 bolt,put 3.42's back in,auburn pro series LSD and did a good weld job to the axle tubes, I busted the driver side of the torsen case off and really wanted to fab an 8.8 but dont have a D/D to take time for mods but I need a good trq arm if u end up parting with it, or LCA's, or to know who u are lol.