Brand New Ported All-Pro Cathedral Port Heads Assembled **$2200 Shipped**
07-15-2011, 10:44 AM
#1
Launching!
Thread Starter
iTrader: (17)
Join Date: Jun 2006
Location: Tulsa, Ok
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
Brand New Ported All-Pro Cathedral Port Heads Assembled **$2200 Shipped** Category: Racing Parts
Price: $2200
Location (State): OK
Item Condition: Brand New
Shipping Information: Item Can be Shipped
LS Engine?: Fits LS Engine
Price $2200 Firm...Complete and ready to go.
An equivalent head setup from Mast or to replicate this setup from All-Pro would run anywhere between $3700-$4000.
Payment option: Paypal (to keep me as the seller and the buyer protected this is my preferred payment method, I also have a paypal debit card and I'm a verified member)...I would also accept Cashiers Check or Cash if local.
Contact Info:Feel free to PM me...Or my personal email is Teh.brandon@yahoo.com... or call my cell @ 9183610920
Recently I have decided to sell my project 415ci C5 build due to the starting of a new project. That said I've sold everything with the exception of these heads. Ive sold my Vic Jr with spray bars and 6061 elbow(on yellowbullet)/Ported LS2 TB(LS1tech)/injectors(LS1tech)/shortblock,trans,rear,roller with all accessories(locally). All that's left are my extremely nice heads.
These come fully assembled and ready to bolt on all that is needed are rockers.
I really liked these heads and I wouldnt be selling them if I didnt have an opportunity for another project. Therefore I'm looking to off load these sooner than later
These are a very nice aftermarket cast head. Here is a link to the PDF provided by All-Pro with detailed information on the heads:
http://www.allproheads.com/images%20...LS1-2_2-08.pdf
Specs specific to this item:
Aftermarket Cast...thick deck good for F/I or Nitrous
244cc runners
Ferrera Stainless Competition Valves 2.08/1.60
Comp Cams dual valve springs/Ti retainers
8mm bronze valve guides (provided by All-Pro)
Locks and Shims (provided by Folks Auto Machine)
Milled to 62cc
Competition Valve Job
Ported intake and exhaust ports(all port work/assembly done by Folks Auto Machine)*these flowed 354@.600
Folks also did some work to the Spark Plug Ports for better alignment
Pictures
AS CAST FROM ALL-PRO
VALVE GUIDES
AFTER PORTING-INTAKE
EXHAUST
CHAMBERS
I can take more pictures upon request...don't hesitate to contact me with any questions or concerns. Thanks
Brandon
Last edited by awd2rwd; 08-29-2011 at 09:50 AM.
07-16-2011, 03:13 AM
#4
Launching!
Thread Starter
iTrader: (17)
Join Date: Jun 2006
Location: Tulsa, Ok
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
I run into some problems with there website sometimes....see if this link below works better.
http://www.allproheads.com/images%20...LS1-2_2-08.pdf
I would suggest using them on a 4+bore as that is what they are best suited for and what you would see full potential on but you can still use these on a 346ci. Ill try to find this thread over on yellowbullet discussing big bore heads on smaller cubic inch setups.
Feel free to contact me with any other questions.
Thanks
Trending Topics
07-21-2011, 09:02 AM
#13
Launching!
Thread Starter
iTrader: (17)
Join Date: Jun 2006
Location: Tulsa, Ok
Posts: 251
Likes: 0
Received 0 Likes
on
0 Posts
Not sure if the previous pictures were showing up as I think my album was set to private....if someone could let me know if the pictures are showing up that would be great 
