Can someone check out my tune?
#21
TECH Enthusiast
Thread Starter
iTrader: (71)
Join Date: Dec 2006
Location: Chattanooga,TN
Posts: 737
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here is my log from sspddmon - Michael-Jerry Tune.tun. I didnt have all the right PIDS active when I done it. I didnt know til after I started. The car felt way better, but had a slight miss sometimes in the the lower RPM range. I didnt get on it hard til near the end because of traffic. Thanks again guys and let me know watcha think.
#22
TECH Addict
iTrader: (10)
Join Date: Jun 2004
Location: Commerce Twp, MI
Posts: 2,918
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here is my log from sspddmon - Michael-Jerry Tune.tun. I didnt have all the right PIDS active when I done it. I didnt know til after I started. The car felt way better, but had a slight miss sometimes in the the lower RPM range. I didnt get on it hard til near the end because of traffic. Thanks again guys and let me know watcha think.
#24
TECH Addict
iTrader: (10)
Join Date: Jun 2004
Location: Commerce Twp, MI
Posts: 2,918
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
I pulled some timing since you were seeing Knock Retard in your log.
It's hard to tell what's going on in your log without any AFR feedback (nothing from the NBO2's and no WBO2).
Some things for concern...
You're logging WAY too many pids. You don't want to exceed 24 channels, which usually means less than 19 pids (because some take 2 channels). So, when you pick pids on the F8 tab, keep an eye on the bottom where it tells you how many of each you have.
It appeared you were seeing LTFT's in the log. Did you turn them back on after I turned them off? They looked like they were active, as if you were in closed loop.
Lastly, if you're still using the MAF, you need to log GM.CYLAIR_DMA - not GM.DYNCYLAIR_DMA. The second one is for speed density calculations.
Check the pic I uploaded below. It has some basic pids to log. Try logging just those and that should help you out.
It's hard to tell what's going on in your log without any AFR feedback (nothing from the NBO2's and no WBO2).
Some things for concern...
You're logging WAY too many pids. You don't want to exceed 24 channels, which usually means less than 19 pids (because some take 2 channels). So, when you pick pids on the F8 tab, keep an eye on the bottom where it tells you how many of each you have.
It appeared you were seeing LTFT's in the log. Did you turn them back on after I turned them off? They looked like they were active, as if you were in closed loop.
Lastly, if you're still using the MAF, you need to log GM.CYLAIR_DMA - not GM.DYNCYLAIR_DMA. The second one is for speed density calculations.
Check the pic I uploaded below. It has some basic pids to log. Try logging just those and that should help you out.
#26
Banned
iTrader: (10)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
As for running the maf, if the VE is not spot on, running the maf will make it more forgiving. If you want to dial in the VE, then turn off the maf, and set it up to tune in SD. Then once thats done, you can decide whether you want to re-enable the maf or not.
#28
TECH Addict
iTrader: (10)
Join Date: Jun 2004
Location: Commerce Twp, MI
Posts: 2,918
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
With the pids recommended and the tune I uploaded, you can keep an eye on the O2 voltages to get an idea of where your AFR is. Values less than 450~500mV are leaner than stoich. Values greater are richer than stoich.
#30
TECH Enthusiast
Thread Starter
iTrader: (71)
Join Date: Dec 2006
Location: Chattanooga,TN
Posts: 737
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here is a new log. Corrected with the 2nd tune. I unplugged the MAF for speed density. It blows out black smoke at idle and it didnt before hand. I guess the maf didnt compensate for the a/f.
#31
Banned
iTrader: (10)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Theres more you need to do than just unplug it to get it in SD to tune. The black smoke just means the VE table is way off. It (the VE) needs to be tuned. If speed demon dont get ya straight, post up and I'll see what I can do. Do you know how to use your charts in the scanner?
#34
TECH Addict
iTrader: (10)
Join Date: Jun 2004
Location: Commerce Twp, MI
Posts: 2,918
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
![Winky](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_wink.gif)
So, this 2nd log was with the MAF unplugged? Funny thing is, it appears when you get on the gas hard (>60% throttle), your O2mV were 920~930 for the most part. If that's a sign of anything, I'd say things are ok there. Spark wise, you may need to pull a degree of timing around peak torque if you continue to see knock retard there.
I'd be curious to see how the second tune does exactly how it is with the MAF plugged in. No unplugging sensors, no switching on closed loop or LTFTs, etc.
#38
TECH Addict
iTrader: (10)
Join Date: Jun 2004
Location: Commerce Twp, MI
Posts: 2,918
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
![Wavey](https://ls1tech.com/forums/images/smilies2/wavey.gif)
Either way....it looks lean with the MAF enabled based on the LTFT's. I don't quite understand why unless you're changing the tune that I uploaded. Also, you might want to check your throttle position sensor and wiring. It seems to be very jumpy.
Last edited by SSpdDmon; 11-28-2007 at 06:18 PM.
#39
TECH Enthusiast
Thread Starter
iTrader: (71)
Join Date: Dec 2006
Location: Chattanooga,TN
Posts: 737
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Sorry I misunderstood what you typed. I will change it tomorrow then log. Another thing the traction control is only activated sometimes. I think I may have a bad tps wire.