what did you do to your firebird today?
#282
Well actually this was a couple days ago, but I went to pick it up from having the engine rebuilt with forged pistons and rods and a new fuel system. Went to start it and this happened, so back to the drawing board. Fuel pressure regulator had a tear in the diaphram.
#283
That's MISTER MODERATOR
iTrader: (9)
I FINALLY mounted the electric scissor jack I've been draging around for like a year in the stock location. It just took a longer bolt and a fender washer. You wouldn't notice the slight bump in the carpeting unless I pointed at it.
I installed the ebay tail light I bought.
I deflated the GTO spare to get it to fit in the quarter panel. No go. Contemplating the next trick.
I installed the ebay tail light I bought.
I deflated the GTO spare to get it to fit in the quarter panel. No go. Contemplating the next trick.
#287
TECH Junkie
iTrader: (104)
Before & After.
Early spyshots of the 'after' because it's still up on jackstands in the garage.
Still working on re-finishing the calipers/rotors, & the Linelock.
Went from the two-piece Corvette FRC's to a one-piece full cover.
Went from the BMR STB to the Hotchkis.
Added the front bumper insert.
As mentioned before, repainted/smoothed the Donaldson Blackwing airlid.
(No, I'm not gonna paint this washer bottle. But if I find a spare, I'll paint it to match.)
I'll probably also take it to the paint shop & have the inner fenders clearcoated. Probably won't fill the holes tho, & simply leave the plugs.
That way, ..., just in case, ...
When spring hits & I can get it outside with no snow, I'll get another better 'after' shot.
Early spyshots of the 'after' because it's still up on jackstands in the garage.
Still working on re-finishing the calipers/rotors, & the Linelock.
Went from the two-piece Corvette FRC's to a one-piece full cover.
Went from the BMR STB to the Hotchkis.
Added the front bumper insert.
As mentioned before, repainted/smoothed the Donaldson Blackwing airlid.
(No, I'm not gonna paint this washer bottle. But if I find a spare, I'll paint it to match.)
I'll probably also take it to the paint shop & have the inner fenders clearcoated. Probably won't fill the holes tho, & simply leave the plugs.
That way, ..., just in case, ...
When spring hits & I can get it outside with no snow, I'll get another better 'after' shot.
#290
Last edited by Suzaku; 01-25-2011 at 09:16 PM.
#294
I finally put on my shocks and spring and front discs and pads... It's almost there.. Part of me just wants to go and buy a car I won't have to do anything with though...
The following users liked this post:
Bruthajoe (03-04-2020)
#295
Replaced the screws with a screw and nut today.
Started working on my new dash pad.
The following users liked this post:
Bruthajoe (03-04-2020)
#297
TECH Fanatic
iTrader: (9)
FINALLY got my replacement rear end for the Trans Am delivered today! Came with everything, brakes, anti-sway bar (I'll be re-using my WS6 one) and shocks. I need the shocks too since mine are squeeking and crappy. I'll be cleaning all the parts up tomorrow and hopefully installing it Saturday. Only down side is that it's geared 2.73. A friend said it'll take a while to get there, but I'll be able to do almost 200! LMAO The fuel economy will be helpful during this long build phase it's in anyway until I can get a 9" in.
#299
got a new whisper lid, detailed and did a 180 for my 7 year old son in the parking lot next to my house.. he loves it..how many of you have kiddos that love this ****?... be honest.. lol