New Hooker Fox Body Mustang LS Swap System Preview Thread
#142
TECH Junkie
Thread Starter
Hey Andrew. Oh yeah, the effort expended to design and build the validation fixture is going to be rewarded on a few future Fox Body projects...the LT swap you mentioned and a Coyote engine swap set-up will be the most immediate.
#144
TECH Junkie
Thread Starter
Thanks for sharing your impression of the environment at Holley...there are a lot of skilled, enthusiastic folks there working hard to bring quality products to the market. I'm glad you were able to visit.
#146
TECH Senior Member
iTrader: (7)
Looks like the engine can sit a lot lower. Is that desirable for cars that have lowered suspension?
Maybe these mounts can have two positions: high and low? Just thinking out loud...
Andrew
Maybe these mounts can have two positions: high and low? Just thinking out loud...
Andrew
#147
TECH Junkie
Thread Starter
The first set depicted maintains the stock crankshaft height and inclination angle.
Last edited by Toddoky; 04-12-2017 at 05:32 PM.
#148
TECH Junkie
Thread Starter
Here's comparative shots of the engine height with the 1/2"-drop engine brackets Andrew. At this engine height, the stock truck intake manifold and alternator/bracket will clear the stock hood.
Incidentally, you can achieve the same underhood clearance with the standard Hooker Fox body brackets used on the stock OE and Maximum Motorsports K-members by using 1/2" K-member shims and you'll still end up with a steering rack height that's far cheaper/easier to achieve acceptable bump-steer with compared to the AJE and Team Z Motorsports K-members.
The Hooker system of parts will finally allow Fox body LS swaps to be carried out in stages as one's budget permits, instead of making the replacement of other parts (i.e. aftermarket K-members, bump-steer kits, steering shafts) a requirement just to get the engine in.
Incidentally, you can achieve the same underhood clearance with the standard Hooker Fox body brackets used on the stock OE and Maximum Motorsports K-members by using 1/2" K-member shims and you'll still end up with a steering rack height that's far cheaper/easier to achieve acceptable bump-steer with compared to the AJE and Team Z Motorsports K-members.
The Hooker system of parts will finally allow Fox body LS swaps to be carried out in stages as one's budget permits, instead of making the replacement of other parts (i.e. aftermarket K-members, bump-steer kits, steering shafts) a requirement just to get the engine in.
Last edited by Toddoky; 04-12-2017 at 05:36 PM.
#151
TECH Junkie
Thread Starter
Update: After completing the validation process, the measured results relative to changing from the stock height engine brackets to the 1/2"-drop engine brackets are as follows:
Engine inclination angle change- 2.2 to 1.4 degrees
Ground clearance decrease at header collectors- 1/4"
Ground clearance decrease of exhaust system rear of X-pipe inlets- 0"
The engine inclination angle change will be even less when the car is equipped with a transmission that has a mount positioned further rearward than the TH350/PG mount position used in the mock-up (i.e. T56, TH400 or 4L80).
The ground clearance decrease is as minimal as it is due to the header collectors being located closer to the transmission crossmember (fulcrum) than to the engine brackets.
Last edited by Toddoky; 04-13-2017 at 11:17 AM.
#153
#154
TECH Junkie
Thread Starter
What I can tell you is the Hooker brackets maintain the stock engine offset to provide compatibility with the Hooker transmission crossmembers. That characteristic means you will be able to install a Powerglide, TH350, TH400, 2004R, 4L60-4L70, 4L80-4L85, T56, T56 Magnum or TKO engine into a Fox Body behind an LS using the Hooker engine brackets and they will all be compatible with the Hooker headers.
If the AJE brackets center the engine in the K-member, then it is likely to cause interference between the headers and the steering shaft.
#155
TECH Junkie
Thread Starter
I have an important application update to report from the results of a design review I just wrapped-up with management...
We will be releasing two sets of engine brackets each for the AJE and Team Z Motorsports K-members to provide the user with the choice of installing the engine at the stock crankshaft height, or at a 1/2" dropped position.
This will provide a user the ability to achieve the different advantages inherent to each position.
The stock crankshaft height position will provide maximum header ground clearance and the most room available under the oil pan to use offset rack bushings to assist in adjusting the bump-steer of the front suspension. This is also the height you would want to use if you are only moderately lowering the car (1" drop) and don't want to have to invest in adjustable rear upper control arms for resetting your pinion angle.
The 1/2" drop crankshaft position will provide extra under-hood clearance (i.e. fitting the truck accessory drive alternator under the stock hood), the greater ability to dial in optimized U-joint working angles on cars lowered more than an inch, and extra transmission clearance for top-side challenged transmission installations such as the TKO transmissions. These advantages come at the cost of approximately 1/4" less ground clearance of the header collectors.
We will be releasing two sets of engine brackets each for the AJE and Team Z Motorsports K-members to provide the user with the choice of installing the engine at the stock crankshaft height, or at a 1/2" dropped position.
This will provide a user the ability to achieve the different advantages inherent to each position.
The stock crankshaft height position will provide maximum header ground clearance and the most room available under the oil pan to use offset rack bushings to assist in adjusting the bump-steer of the front suspension. This is also the height you would want to use if you are only moderately lowering the car (1" drop) and don't want to have to invest in adjustable rear upper control arms for resetting your pinion angle.
The 1/2" drop crankshaft position will provide extra under-hood clearance (i.e. fitting the truck accessory drive alternator under the stock hood), the greater ability to dial in optimized U-joint working angles on cars lowered more than an inch, and extra transmission clearance for top-side challenged transmission installations such as the TKO transmissions. These advantages come at the cost of approximately 1/4" less ground clearance of the header collectors.
#156
TECH Junkie
Thread Starter
OK guys, I've taken photos of the stock height and 1/2" drop engine brackets for the AJE K-member with the Holley 302-1 and 302-2 oil pans as well as the Weiand fabricated steel oil pan so that a clear visual representation of the clearance difference between them can be observed. The Holley 302-1 is shown in the first to photos followed by the Holley 302-2 and finally the Weiand pan. The 302-1 is just barely kissing the top of the PS rack with the 1/2" drop brackets, but would easily clear a manual rack...
#158
I can't say what the AJE brackets provide in terms of the engine fore/aft position or offset, or crankshaft height/inclination angle as I don't have them in my possession to evaluate.
What I can tell you is the Hooker brackets maintain the stock engine offset to provide compatibility with the Hooker transmission crossmembers. That characteristic means you will be able to install a Powerglide, TH350, TH400, 2004R, 4L60-4L70, 4L80-4L85, T56, T56 Magnum or TKO engine into a Fox Body behind an LS using the Hooker engine brackets and they will all be compatible with the Hooker headers.
If the AJE brackets center the engine in the K-member, then it is likely to cause interference between the headers and the steering shaft.
What I can tell you is the Hooker brackets maintain the stock engine offset to provide compatibility with the Hooker transmission crossmembers. That characteristic means you will be able to install a Powerglide, TH350, TH400, 2004R, 4L60-4L70, 4L80-4L85, T56, T56 Magnum or TKO engine into a Fox Body behind an LS using the Hooker engine brackets and they will all be compatible with the Hooker headers.
If the AJE brackets center the engine in the K-member, then it is likely to cause interference between the headers and the steering shaft.
#160
TECH Junkie
Thread Starter