Help me install ls6 intake? Mt.Belvieu area
Help me install ls6 intake? Mt.Belvieu area I am hoping to get some help today, tomorrow , or Sunday. I will buy all the beer you can drink and a little cash or some cash. Pm me. I am working on it now, but hoping someone who has done a few can save me some time.
Here is where I am at.
Here is my intake.
Here is where I am at.
Here is my intake.
It will get done no problem if no help. I am really just wanting someone that knows all the tubing mods and such to come drink beer with me and listen to loud heavy metal. Charlie C5 you working today?
Man, If I lived by you I would help you, but its really easy.
Make sure you pull the connector and hoses off the back, and disconnect the fuel lines and plug on the driver side. After that all it is disconnecting the injector plugs, and taking all of the 8mm bolts out.
You will probably want to take off the strut tower brace.
Make sure you pull the connector and hoses off the back, and disconnect the fuel lines and plug on the driver side. After that all it is disconnecting the injector plugs, and taking all of the 8mm bolts out.
You will probably want to take off the strut tower brace.
Trending Topics
Thanks Josh for the info. I stopped by after work and bought both of the new style sensors $$$$$$. Then stopped by the junkyard and found 2 of those pigtails. After I pulled my intake, I was puzzled. I remembered what you said about 98 sensors being different.......and then it hit me. My motor is a 02 lol. One of the sensors was quite rusted. Anyway, I will finish up this weekend if I don't have to work. I am still thinking about doing that LS6 valley cover, I will read up some more on it.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Yea that’s the new style. I try to find the old, I might have a picture or too...Sorry about tonight, I forgot I had softball tonight. and have it again tomorrow but its looks good so far. I’ll be around till Friday morning then I be back hopefully Sunday..
I ended up working the past few weekends but spent a couple hours on it last night. The rubber gasket for the front knock sensor was full of crud. I tried to clean it out and finally decided to pull it hoping not very much would fall inside.
I kinda freaked out. Went and got q-tip and oil and tried to get it out. Then went and got vacum cleaner. Think I got most of it. Will I be ok if i run engine for 10-15 seconds then change oil?
Here is the 04 vette valley cover I bought.
Also, my throttle body came in. I think Bo did a good job.
I am a little worried about the debris and 30-40 mesquitos that may be under this towel. I hope I haven't messed up so far.
I also bought a brand new knock sensor wiring harness for $15 from someone off of this board. Let me know if you have any suggestions I am a noob to this.
I kinda freaked out. Went and got q-tip and oil and tried to get it out. Then went and got vacum cleaner. Think I got most of it. Will I be ok if i run engine for 10-15 seconds then change oil?
Here is the 04 vette valley cover I bought.
Also, my throttle body came in. I think Bo did a good job.
I am a little worried about the debris and 30-40 mesquitos that may be under this towel. I hope I haven't messed up so far.
I also bought a brand new knock sensor wiring harness for $15 from someone off of this board. Let me know if you have any suggestions I am a noob to this.
Banned
Joined: Apr 2007
Posts: 269
Likes: 0
www.ls1howto.com step by step instructions there. Like others have said this is super easy, it's like a 45min-1 hour job tops
