Smartass6885

iTrader: (3)

what do u charge to narrow the rear end? I was thinkin of knockin half an inch off each side. let me know. Also, do u carry a heavy duty DS that will work with the 9" in a 6spd car? Need somthin that will take 5-6k rpm clutch drops with 480rwhp. Thanks alot.

-Blaze

EPP

iTrader: (22)

$110.00 is what Moser charges to shorten a rear-end housing. They only give us a $10.00 discount off the price, so give them a call at 260 726-6689 to make arrangements to have it shipped to them.

Our PST 3.5" aluminum driveshaft is rated at 1200 hp, and is the correct length. It comes with a heavy duty 1350 U Joint, so no weaker conversion U Joint is used. This driveshaft will handle the abuse! Bob

slmdLS1

iTrader: (8)

Bob, is the aluminum center sectioned, Moser 9" with a truetrac, price $2400 shipped?

EPP

iTrader: (22)

No, the Moser nodular iron center section with the Moser 9 inch/Truetrac is $2,400.00 shipped. Moser does not offer their aluminum center section with the Truetrac. I know it is offered with a spool, and I believe it is offered with the Auburn center. Thanks for inquiring. Bob

you2slo

Check PMs

z28pat

iTrader: (10)

HI,
newbie question,
what would I need aside from what you send with the Moser rear ends to bolt it in to my car?

pat

EPP

iTrader: (22)

A new U Joint if you have the stock driveshaft with it's 1310 yoke. Napa pn# 240-0447 goes for $32.00. 3 quarts of non synthetic gear lube, 2 ft of 1/4 vacuum hose for the vent line, two 3.00" exhaust clamps. You use the U part of the exhaust clamps to secure the rear sway bar, and reuse the bottom part of the sway bar bracket after elongating the holes towards the outer ends. The reason for doing this is the Moser housing is larger in diameter than the stock housing. The 3.00" U Bolts fit over the housing.
You also need a bearing press to press off the old axle bearings to remove the brake backing plates that are reused. Most Napa and small shops have a press, it only takes several minutes to do this. You reinstall the backing plates on the new axles, and press on the new Moser supplied axle bearings. Instructions are included from Moser for doing this. The center cover on the new Moser 12 bolt does not ever come off for doing this procedure, by the way. The axles are retained at the ends, as there are no C Clips.
Hopefully this helps. Bob

hazard2k

iTrader: (10)

You dont have to press off the bearings on the stock rear end, they are not attached to the axle. You pull the c-clip and the axle slides out, then 4 bolts hold on the brake bracket to the rear end housing. You do have to press the bearings onto the new axle however. -Jeff

SVC707

iTrader: (33)

please pm me a total for 9" truetrac posi unit, 31 spline axles, drain/fill plugs, no abs, 3.50 gear ratio along with correct driveshaft for 6 speed transmission

EPP

iTrader: (22)

$2430.00 for the Moser 9 inch with the Truetrac, 31 spline axles, drain/fill plugs, no ABS/TCS, and 3.50 gear ratio. This includes shipping. The PST 3.5" aluminum driveshaft, rated at 1200 hp is $399.99 plus shipping. Total is $2830.00 and I'll throw in free shipping on the driveshaft, so the total is $2,830.00. Thanks! Bob

Bill'sWS6

iTrader: (6)

Please check your Private Message Box.. I am interested in a rear end, ASAP.

Thanks,

Bill

EPP

iTrader: (22)

08-15-2006 01:41 PM
by Bill'sWS6

I don't see your post? Bob

Zitty'sZ

iTrader: (29)

I have a UMI adjustable torque arm for my car , will it work with your 12 bolt rears? Also. could you tell me how much shipping would be to 33033? Thank you, Richard.

Phynix

iTrader: (3)

does the 12 bolt come with the 1310 yoke or the 1350, and how much shipping to southern california, somewhere around 92704, have the money and ready to buy. would also like to know what gear sizes you have above 410s, please PM me

EPP

iTrader: (22)

1350 is the standard yoke size, although it can be built with a 1310.

I would estimate shipping to be in the $200.00 neighborhood. It is very hard to calculate shipping as it seems to change daily. Right now fuel prices are down.

4.30, 4.56, 4.88, 5.14 and 5.38 gear ratios are offered above 4.10.

Thanks for inquiring. Bob

EPP

iTrader: (22)

Yes, the UMI will work with the Moser 12 bolt. Approx $150.00 to Homestead, Florida. Thanks for inquiring. Bob

slmdLS1

iTrader: (8)

bump for Bob, got my rear(Moser 9", 31spline, truetrac) in a timely manner last week, now to find the time to put it in, lol.

jdizzle

do you guys give military discounts?

EPP

iTrader: (22)

Thanks, I appreciate it. Bob

Bill'sWS6

iTrader: (6)

Another Bump:

I just wanted to give a special thanks to Don and everyone else over at Exotic Performance Plus. I went to them for my new 9” rear end and install. Everyone there was great to deal with from start to finish. They took the extra time to explain things when I had questions, no rushing me at all.

All I can say is the sales and service are great. If you are looking for a new rear end. Or, anything else since they stock a ton of parts.

Oh yea one other item….. If you need a tune this is the place. I saw a car come in with mid 300RWHP/RWTQ and leave with an additional 100RWHP/RWTQ, this on a Mustang Dyno.

Always nice to find a place like this, I’ll be back.

Bill