UMI k member... ITS HERE
07-12-2006, 05:18 PM
#61
I smell trolls.... 6 posts since 9/2004 and 12 posts since 7/2003 respectively. Also notice that of Blahman's 6 posts, at least 3 were bashing other products, and another one was recommending a specific brand, and another was offering some advice about some parts from same said company. So 5 of 6 posts seem to have some bias.
Believe what you all want. I'm not putting much stock in it, sorry. I've seen the part. I've been to the UMI shop more than once and have seen the welds and workmanship. I'll vouch for the parts personally.
This K-member is so far beyond what the others ones available are it's silly. The fact there are two cross-tubes and not just one should be a dead giveaway that skimping wasn't in the plan, and that UMI's is much tougher than the others. It's the only one I'll sell.
Believe what you all want. I'm not putting much stock in it, sorry. I've seen the part. I've been to the UMI shop more than once and have seen the welds and workmanship. I'll vouch for the parts personally.
This K-member is so far beyond what the others ones available are it's silly. The fact there are two cross-tubes and not just one should be a dead giveaway that skimping wasn't in the plan, and that UMI's is much tougher than the others. It's the only one I'll sell.
__________________
www.stranoparts.com --814-849-3450
18 SCCA National Championships in house, many more for our customers prove we know our stuff.Talk is cheap, results matter.
Check out our KONI prices, our Master Cylinder Brace, and new Xtracker Hub/wheel bearing upgrade kits!
www.stranoparts.com --814-849-3450
18 SCCA National Championships in house, many more for our customers prove we know our stuff.Talk is cheap, results matter.
Check out our KONI prices, our Master Cylinder Brace, and new Xtracker Hub/wheel bearing upgrade kits!
Just dont like to post much. 
07-13-2006, 08:54 AM
#70
Tech Resident
i haven't done any suspension mods to my car yet, but i'm sure they lay waiting in the future. just by reading about UMI's comments from users - which are all amazing - they'll be my choice i'm sure. the fact that they deliver such consistent quality and are in some cases HUNDREDS cheaper than competitors blow my mind! they're prices are so much lower than BMR's counterparts and they all seem to have equal if not better quality.
just thought i'd throw that in to voice my opinion.
just thought i'd throw that in to voice my opinion.
07-14-2006, 05:21 PM
#72
Originally Posted by BlahMan
Blah blah blah blah blah blah blah blah blah blah blah blah blah blah blah. Blah blah blah blah blah (woof woof woof) blah blah blah blah blah blah.
Blah blah blah blah blah blah blah blah
Blah blah blah blah blah blah blah blah blah, I must be going blind blah blah blah blah blah blah blah blah blah, blah blah blah blah.
Blah blah blah blah blah blah blah blah
Blah blah blah blah blah blah blah blah blah, I must be going blind blah blah blah blah blah blah blah blah blah, blah blah blah blah.
07-14-2006, 05:33 PM
#73
Blahman or should I say "Kat" what is your objective here and on the other boards? To run UMI products down so people will tend to purchase items manufactured from the company you work for, Spohn.
Your post is very immature and says little about you and your position at Spohn, on a side note you make Spohn look immature as well. I suggest you grow up and lose the jealous attitude.
There is plenty of business out there for us all; I just don't have to down another company’s product to make a sale
Here is another post from Blahman or Kat, I suggest you register and read it.
http://www.nethirdgen.org/forum/showthread.php?t=42678
Your post is very immature and says little about you and your position at Spohn, on a side note you make Spohn look immature as well. I suggest you grow up and lose the jealous attitude.
There is plenty of business out there for us all; I just don't have to down another company’s product to make a sale
Here is another post from Blahman or Kat, I suggest you register and read it.
http://www.nethirdgen.org/forum/showthread.php?t=42678
07-14-2006, 05:44 PM
#74
Are things that slow that people need to look for reasons to run everyone else down? IMO, instead of wasting time posting about someone elses products (in a severly vindictive way to boot), maybe put the time and energy into figuring out why a product with such "bad" welds is selling so well - and how such a young company has taken off so well. But, what do I know, I don't even have a fbod anymore. 
I will just ***ume you will defend your comments to be because you don't want to see someone get ripped off with sub-par craftsmanship, but I would say that the buying public has unlimited resources to these suspension companies to form their own opinions from real experiences, not some spiteful babble from an internet mudslinger who has a personal vendetta against UMI.
I will just ***ume you will defend your comments to be because you don't want to see someone get ripped off with sub-par craftsmanship, but I would say that the buying public has unlimited resources to these suspension companies to form their own opinions from real experiences, not some spiteful babble from an internet mudslinger who has a personal vendetta against UMI.
07-14-2006, 06:02 PM
#75
Originally Posted by UMI Performance
Here is another post from Blahman or Kat, I suggest you register and read it.
http://www.nethirdgen.org/forum/showthread.php?t=42678
http://www.nethirdgen.org/forum/showthread.php?t=42678
Originally Posted by UMI Performance
Here is another pic from Blahman or Kat, aka T-Money, aka Chanel.
They call me T-Money baby!
They call me T-Money baby!
Holla at 'cha bitches!*EDIT* these pics don't have anything to do with UMI, but they sure go good with the immaturity in this thread.
Last edited by demonspeed; 07-17-2006 at 08:50 AM.
07-18-2006, 11:16 AM
#78
Look who Ryan and I found this weekend? Yes, this car obviously belongs to Blahman aka Kat aka Tmoney! Wow, for such an authoritive figure about fbody suspension, you'd think he'd drive something besides a Civic Si!
Last edited by demonspeed; 07-18-2006 at 11:56 AM.
for the purposes of this thread, it is! 