Who was this? (Yellow C5 Z06 w/yellow wheels, DFW)
12-09-2009, 09:12 PM
#61
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
Here's a link to a new video posted of the Z06 I ran.
Have not verified yet if it was making 647rwhp when we ran.
http://www.youtube.com/watch?v=8VbPRvNO0Vw
Have not verified yet if it was making 647rwhp when we ran.
http://www.youtube.com/watch?v=8VbPRvNO0Vw
12-10-2009, 08:41 PM
#62
On The Tree
iTrader: (11)
Join Date: Jun 2005
Location: Left Texas, now in Camarillo, CA
Posts: 140
Likes: 0
Received 0 Likes
on
0 Posts
I built and tuned that vette and it was rev limited to only make 600rwhp when you ran him. I agree both of you need to line up on the right road and make a good clean run and see how it ends. Both are bad cars and it should make for a sweet vid if we can make that happen. He's down for another run.
12-10-2009, 08:48 PM
#63
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
I built and tuned that vette and it was rev limited to only make 600rwhp when you ran him. I agree both of you need to line up on the right road and make a good clean run and see how it ends. Both are bad cars and it should make for a sweet vid if we can make that happen. He's down for another run.
Yeah, I figured he either spun real bad, etc etc after I found out he made 640+rwhp and I pulled like I did. Like stated above I might have been making slightly more than 9psi, but not much.
And BTW, I am down like James Brown on a video!
12-16-2009, 08:00 PM
#69
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
Nope, I am in the middle of yanking the 6sp and installing aTH400. Tired of dealing with hydraulic issues.
Should be ready in a few more weeks and then I will be knocking on the low 10's.
Should be ready in a few more weeks and then I will be knocking on the low 10's.
Last edited by Vcious04; 12-16-2009 at 08:07 PM.
12-16-2009, 08:06 PM
#70
TECH Fanatic
Thread Starter
iTrader: (16)
Join Date: Dec 2005
Location: Alvarado, Texas
Posts: 1,299
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Nine Ball
= sausage or chain. The proper word is "Lengths", as in putting "several car lengths, or bus lengths" on them.
FYI, it was lengths, as in cars.
Originally Posted by T2SLS1
Who in the DFW area is driving around making over 980rwhp? not everyday but on occasions I have a couple of questions?
12-17-2009, 03:29 AM
#71
On The Tree
Join Date: Nov 2008
Location: Fort Worth, TX
Posts: 105
Likes: 0
Received 0 Likes
on
0 Posts
What?! It better go nines if you're putting in an auto! What about the rearend and I thought you fixed the hydraulics?
