1991 Corvette, low 11 second daily driver with 400+ RWHP
#1
On The Tree
Thread Starter
Join Date: Jan 2002
Location: Raleigh, NC
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
1991 Corvette, low 11 second daily driver with 400+ RWHP
Year: 1991
Make: Chevrolet
Model: Corvette
Price: $9500
Mileage: 86000
Private or Dealer Listing: Private Listing
Location (State): NC
Color: Black
Transmission: Manual
Drivetrain: Rear Wheel Drive
LS Engine?: Car has other engine
The details are:
I bought the car in 2005 with 61,000 miles on it. I bought it from the second owner, and it was completely stock. It was a Florida car it's entire life, so the paint is slightly faded, but from 5 feet the car looks fantastic. The car now has 86,XXX miles on it.
The car is in Raleigh, NC. I would be willing to deliver the car within a reasonable distance.
The car, is daily driver friendly, traps 122+ MPH in the quarter, and runs low 11's. AC still works, and the car is easy to drive.
Right now, there is about $10,000 worth of mods done to the car. The motor, plus heads, cam, intake, and all the ancillaries was about $6500, the drive train mods are about $2500, and all the other small things add up to about 10K. I have receipts for almost everything.
The mods are:
383 stroker
-Only about 5500 miles on the new mill. I broke the stock motor about 2 years ago and had to re-finance the car to build the new engine. I also did a pretty extensive comparison of 2 cylinder heads that you can read about here - http://www.corvette-guru.com/modules...d=7225&forum=1
-Eagle cast crank. 650-700 RWHP at a reasonable RPM (below 7K) and the crank will live forever.
-6 inch forged H beam rods
-SRP forged pistons with chromoly rings gapped a little wide for nitrous use
-AFR 195 competition port cylinder heads
-Cometic head gaskets
-Comp Cams hydraulic roller, 230/236 - mid 500's on lift, 113 LSA
-Probe 1.6 full roller rockers
-Miniram intake
Other stuff done to the car:
-Hooker long tubes
-Dr. Gas X pipe
-Magnaflow mufflers
-3.90 rear gears
-Centerforce dual friction clutch with single mass flywheel
-Custom made steel half shafts
-Cryo treated spice U-joints
-Cryo treated inner stub axles, differential case, posi unit, gears, and clutches
-In car wideband via PLX and autometer gauge
-B&M ripper shifter
-Walbro 255 LPH intank pump
-Mallory 685 ignition box
-Fabricated aluminum valve covers, powder coated black
The engine is set up to handle up to a 300 HP shot of nitrous. I was planning to use a staged set up with 125 HP in first gear, and another 125 HP in all other gears for a total of 250 HP.
The car made 414 RWHP / 396 RWTQ naturally aspirated. The new engine has never had nitrous through it, but on a 200 shot it should easily eclipse 600 RWHP and 600 RWTQ.
The AC compressor is the original one from 1991. While the AC still works great and blows cold, I have noticed some black dust around the AC compressor after I use the AC. This tells me that the compressor is probably on its way out and will need to be replaced. The car still has R12 in it, so the entire conversion would be necessary.
$9,500 is my asking price.
If you have any questions or would like pictures of anything specific, please feel free to email me, joshkinzey@gmail.com
This is the car after some polish work with a Porter Cable orbital polisher. It shines up incredibly well, but I don't have the time to maintain the finish:
Here's the new mill, before I put it in the car:
Shots of the car:
Again, $9,500. Please feel free to email with questions. I don't have a problem talking about it over the phone as there is a considerable amount of time and money into the car, I just don't want to post my phone number on the forum.
joshkinzey@gmail.com
#5
free bump for a SWEET car
I seem to be a blacksheep for liking C4's more than most all other vettes. I don't know why, they just don't seem as showy to me. They're slow stock but I'd love to build one.
GLWS!
I seem to be a blacksheep for liking C4's more than most all other vettes. I don't know why, they just don't seem as showy to me. They're slow stock but I'd love to build one.
GLWS!
Trending Topics
#10
On The Tree
Thread Starter
Join Date: Jan 2002
Location: Raleigh, NC
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
I finally put spray on the car, so the kit comes with the car. It's had a couple bottles through it tuning it on the dyno and a handful of street pulls. Car made 550 RWHP and 599 RWTQ with a small shot. Haven't stepped it up yet, I'll let the new owner make the call on big they wanna go.
#17
On The Tree
Thread Starter
Join Date: Jan 2002
Location: Raleigh, NC
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
http://s294.photobucket.com/albums/m...er_media_share
Here it is making a pass. This is with the cut-outs open, so you are hearing headers, X-pipe, and about 4-5 feet of pipe.
Here it is making a pass. This is with the cut-outs open, so you are hearing headers, X-pipe, and about 4-5 feet of pipe.
#18
On The Tree
Thread Starter
Join Date: Jan 2002
Location: Raleigh, NC
Posts: 104
Likes: 0
Received 0 Likes
on
0 Posts
Here's a video I made a few days ago for someone who wanted to hear the car. This is through the magnaflow mufflers, cut-outs closed.
http://youtu.be/KN2PjOZozeo
http://youtu.be/KN2PjOZozeo