feeler f/s 94 z28 forged 355 MINT
12-04-2008, 06:25 PM
#1
Staging Lane
Thread Starter
iTrader: (4)
Join Date: Oct 2005
Location: NJ
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
feeler f/s 94 z28 forged 355 MINT ok just seeing if i get any bites. the car is ridiculously clean and it gets comments wherever it goes. sounds awesome.
motor is a fresh less 2000 miles forged 355 mahle raceweight forged aluminum pistons
comp xfi 292
comp hardened pushrods
1.6 roller rockers (pbm)
heads are fully ported with 2.02 1.60 ferrea race stainless valves
intake is ported
full bolt ons
trans was just freshened up when motor was done so it has only 2000 miles on it new hurts shifter and short stick
full umi rear suspension
tubular k member
solid motor mounts
comes with a set of weld pro stars
car has the rare red insert seats in it i have a pic of that
has a 4inch cowl and a ss spoiler
car runs awesome. id like 10,000 for the car....ive attached some pics
front bumper cover has 2 tiny bubbles right at the turn signal. i have a new front bumper. it definitely does NOT need a new bumper. im sure im forgetting alot of stuff. the car has over 12,000 invested
if anyone is serious my number is 908-463-1256 leave a message if i dont answer i will get back to you. i live in nj.
motor is a fresh less 2000 miles forged 355 mahle raceweight forged aluminum pistons
comp xfi 292
comp hardened pushrods
1.6 roller rockers (pbm)
heads are fully ported with 2.02 1.60 ferrea race stainless valves
intake is ported
full bolt ons
trans was just freshened up when motor was done so it has only 2000 miles on it new hurts shifter and short stick
full umi rear suspension
tubular k member
solid motor mounts
comes with a set of weld pro stars
car has the rare red insert seats in it i have a pic of that
has a 4inch cowl and a ss spoiler
car runs awesome. id like 10,000 for the car....ive attached some pics
front bumper cover has 2 tiny bubbles right at the turn signal. i have a new front bumper. it definitely does NOT need a new bumper. im sure im forgetting alot of stuff. the car has over 12,000 invested
if anyone is serious my number is 908-463-1256 leave a message if i dont answer i will get back to you. i live in nj.
12-06-2008, 09:39 AM
#6
12 Second Club
iTrader: (34)
Join Date: Dec 2006
Location: READING Pa
Posts: 712
Likes: 0
Received 0 Likes
on
0 Posts
this was my old car car ran awesome made 432 rwhp on motor i wish i was in a better situation and had the money to buy it back miss it alot i had over 16k invested in it when i sold it free bump good luck selling it hopefully someone gets it who will take care of it
Trending Topics
12-06-2008, 09:47 PM
#8
Bump for a great seller! I can vouch for Joe that he is an honest guy. It's always uncertian when dealing with someone on the board that has a low post count since their reputation is unknown.
I sold one of my vehicles to Joe a couple years ago and he was a 100% strait-shooter, had great communication, and followed through on everything he said.
Jason
I sold one of my vehicles to Joe a couple years ago and he was a 100% strait-shooter, had great communication, and followed through on everything he said.
Jason
12-08-2008, 01:51 PM
#14
TECH Enthusiast
iTrader: (14)
Join Date: Jun 2006
Location: Mohnton, pa
Posts: 552
Likes: 0
Received 0 Likes
on
0 Posts
Ill fill in blanks lol. Car has a pacesetters, loudmouth wiht a moroso spiral flow (sounds badass), zex wet shot, spoiler is GM not aftermarket, hood is a glasstek, msd 6al box, msd coil and wires, K&n setup from Ls1, twin 58mm bbk throttle body, canton valve covers, air/fuel ratio gauges on pillar, 255 in tank pump, new stater, 160 stat, elec water pump, and 95+ msd opti. Car will hold a 150-200 shot. If someone wants a badass lt1 ride this is it. I wish i had the money to buy it. Also has eibach pro kit springs, its a pro fab kmember, rear suspension is all umi. Compression ratio is about 12.1 and WILL run on 93 with no problems. Spec 3 clutch and billet steel flywheel. AC/ABS removed. Might save you some questions Joey.....
12-11-2008, 03:26 PM
#17
Staging Lane
Thread Starter
iTrader: (4)
Join Date: Oct 2005
Location: NJ
Posts: 63
Likes: 0
Received 0 Likes
on
0 Posts
also these rims are probably not coming with the car. i have a set of 17 inch billet wheels on there now. the welds might be included if price is right...make an offer...needs to go soon..
