Thanks to Rob @ Strictly Performance I have a cool exhaust!
#41
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by DEMONBIRD
It started with me buying Hawaii Mark's LT's (to replace the headers and y-pipe that were mangled after the wife drove the car) and went to Strictly Performance to pick up the y-pipe (Mark had left it there)... ![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I didn't realize Hooker's had the huge 3-bolt flange's for connectors and my car being as low as it is I knew it would get ripped off... :help:
SO, Rob recommended me to his exhaust guy (to get them modified to work). I ended up not going with the Hookers (due to ground clearance) but have a really cool custom setup that they did for me...![Mr. Cool](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cool.gif)
I had them cut off the ball flanges from my MAC headers (the headers are 3" but neck down to 2 1/4"... I dremeled it out some but 2 1/2" is all I could get it to and the y-pipe is only 2 1/2" anyways...). They replaced them with V-Band Clamps so it is a STRAIGHT 3" shot from the header into my new, mandrel bent 3" y-pipe...
It then goes into a Flowmaster dual 3" to 4" collector, then into my 4" Mufflex system with Spintech muffler and dual 3" out![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
Should be pretty high flowing (I had ported the MAC's before I installed them as well) and still retain some torque. Definetly more than enough for the F13 on a 112 + 2 that I am about to throw at it![Icon Eek](https://ls1tech.com/forums/images/smilies2/icon_eek.gif)
The best part is there are NO LEAKS, NO VIBRATIONS, NO RUBBING, and NO KNOCKING INTO THE FLOOR
!!!
Anyways, without further ado here's some pics:
NOTE: Yes, the under side of my car needs attention... Places that were "clearanced" will get paint, the rear end will get it's leak fixed when it gets gears as will the tranny's when it gets a stall converter...
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust6.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust5.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust7.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust8.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust4.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust3.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust2.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust1.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust.jpg)
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I didn't realize Hooker's had the huge 3-bolt flange's for connectors and my car being as low as it is I knew it would get ripped off... :help:
SO, Rob recommended me to his exhaust guy (to get them modified to work). I ended up not going with the Hookers (due to ground clearance) but have a really cool custom setup that they did for me...
![Mr. Cool](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cool.gif)
I had them cut off the ball flanges from my MAC headers (the headers are 3" but neck down to 2 1/4"... I dremeled it out some but 2 1/2" is all I could get it to and the y-pipe is only 2 1/2" anyways...). They replaced them with V-Band Clamps so it is a STRAIGHT 3" shot from the header into my new, mandrel bent 3" y-pipe...
It then goes into a Flowmaster dual 3" to 4" collector, then into my 4" Mufflex system with Spintech muffler and dual 3" out
![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
Should be pretty high flowing (I had ported the MAC's before I installed them as well) and still retain some torque. Definetly more than enough for the F13 on a 112 + 2 that I am about to throw at it
![Icon Eek](https://ls1tech.com/forums/images/smilies2/icon_eek.gif)
The best part is there are NO LEAKS, NO VIBRATIONS, NO RUBBING, and NO KNOCKING INTO THE FLOOR
![Driving](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_driving3.gif)
Anyways, without further ado here's some pics:
NOTE: Yes, the under side of my car needs attention... Places that were "clearanced" will get paint, the rear end will get it's leak fixed when it gets gears as will the tranny's when it gets a stall converter...
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust6.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust5.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust7.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust8.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust4.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust3.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust2.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust1.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust.jpg)
#45
TECH Addict
iTrader: (11)
Join Date: Feb 2005
Location: Brunswick, GA
Posts: 2,193
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by DEMONBIRD
I've seen setups they did that were dual 3", over the axle (one where they were both on one side and one where they were on opposite sides) and they were mandrel bent, nice and made no hits on the floor ![The Judge](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_judge.gif)
![The Judge](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_judge.gif)
![Secret2](https://ls1tech.com/forums/images/smilies/LS1Tech/secret.gif)
#46
TECH Apprentice
iTrader: (16)
Join Date: Jun 2004
Location: So Cal
Posts: 305
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by DEMONBIRD
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
Did you see the Medium Blue Metallic Trans-Am when I turned right and you went left? I snapped some pics:
![](http://i31.photobucket.com/albums/c362/markdelisle/MBMTrans-Am1.jpg)
Nice looking rare car and it was clean so I would assume the owner knows he has something cool on his hands... Do you know the car?
I'll try to make it out there tommorrow night...
![Driving](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_driving3.gif)
#50
10 Second Club
iTrader: (44)
Join Date: May 2004
Location: Phoenix, AZ
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by Almostryan3
an A3 and what a gutted car is no street car. I know you didn't say gutted but a diet.
![Offtopic](https://ls1tech.com/forums/images/smilies3/offtopic.gif)
#52
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by XpEdItIoUs
Well it will be on the street more than the track so its a street car, yes i did gutt it but i will still have all panels and carpet.
lol, This is about marks cool new exhaust.
![Offtopic](https://ls1tech.com/forums/images/smilies3/offtopic.gif)
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
#53
10 Second Club
iTrader: (44)
Join Date: May 2004
Location: Phoenix, AZ
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by DEMONBIRD
That's ok, let's keep talking about your car and it's interior panels... WHEN R U GOING TO COME GET MY LEATHER DOOR PANELS FOR $50
?!
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
#55
10 Second Club
iTrader: (44)
Join Date: May 2004
Location: Phoenix, AZ
Posts: 1,658
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by DEMONBIRD
Just name a day and time and I'll be there... Have time off since it is hiatus, also really need some money since it is hiatus ![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
#57
TECH Apprentice
iTrader: (7)
Join Date: Jan 2003
Location: socal
Posts: 377
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by DEMONBIRD
Just name a day and time and I'll be there... Have time off since it is hiatus, also really need some money since it is hiatus ![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
![The Judge](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_judge.gif)