Thanks to Rob @ Strictly Performance I have a cool exhaust!
#1
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
It started with me buying Hawaii Mark's LT's (to replace the headers and y-pipe that were mangled after the wife drove the car) and went to Strictly Performance to pick up the y-pipe (Mark had left it there)... ![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I didn't realize Hooker's had the huge 3-bolt flange's for connectors and my car being as low as it is I knew it would get ripped off... :help:
SO, Rob recommended me to his exhaust guy (to get them modified to work). I ended up not going with the Hookers (due to ground clearance) but have a really cool custom setup that they did for me...![Mr. Cool](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cool.gif)
I had them cut off the ball flanges from my MAC headers (the headers are 3" but neck down to 2 1/4"... I dremeled it out some but 2 1/2" is all I could get it to and the y-pipe is only 2 1/2" anyways...). They replaced them with V-Band Clamps so it is a STRAIGHT 3" shot from the header into my new, mandrel bent 3" y-pipe...
It then goes into a Flowmaster dual 3" to 4" collector, then into my 4" Mufflex system with Spintech muffler and dual 3" out![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
Should be pretty high flowing (I had ported the MAC's before I installed them as well) and still retain some torque. Definetly more than enough for the F13 on a 112 + 2 that I am about to throw at it![Icon Eek](https://ls1tech.com/forums/images/smilies2/icon_eek.gif)
The best part is there are NO LEAKS, NO VIBRATIONS, NO RUBBING, and NO KNOCKING INTO THE FLOOR
!!!
Anyways, without further ado here's some pics:
NOTE: Yes, the under side of my car needs attention... Places that were "clearanced" will get paint, the rear end will get it's leak fixed when it gets gears as will the tranny's when it gets a stall converter...
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust6.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust5.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust7.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust8.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust4.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust3.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust2.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust1.jpg)
![Grin](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_grin.gif)
I didn't realize Hooker's had the huge 3-bolt flange's for connectors and my car being as low as it is I knew it would get ripped off... :help:
SO, Rob recommended me to his exhaust guy (to get them modified to work). I ended up not going with the Hookers (due to ground clearance) but have a really cool custom setup that they did for me...
![Mr. Cool](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_cool.gif)
I had them cut off the ball flanges from my MAC headers (the headers are 3" but neck down to 2 1/4"... I dremeled it out some but 2 1/2" is all I could get it to and the y-pipe is only 2 1/2" anyways...). They replaced them with V-Band Clamps so it is a STRAIGHT 3" shot from the header into my new, mandrel bent 3" y-pipe...
It then goes into a Flowmaster dual 3" to 4" collector, then into my 4" Mufflex system with Spintech muffler and dual 3" out
![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
Should be pretty high flowing (I had ported the MAC's before I installed them as well) and still retain some torque. Definetly more than enough for the F13 on a 112 + 2 that I am about to throw at it
![Icon Eek](https://ls1tech.com/forums/images/smilies2/icon_eek.gif)
The best part is there are NO LEAKS, NO VIBRATIONS, NO RUBBING, and NO KNOCKING INTO THE FLOOR
![Driving](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_driving3.gif)
Anyways, without further ado here's some pics:
NOTE: Yes, the under side of my car needs attention... Places that were "clearanced" will get paint, the rear end will get it's leak fixed when it gets gears as will the tranny's when it gets a stall converter...
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust6.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust5.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust7.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust8.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust4.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust3.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust2.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust1.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust.jpg)
#2
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Here's some pics on the ground for clearance references (it is a LOT better than before, trust me):
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust17.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust15.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust14.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust13.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust11.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust12.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust19.jpg)
Yes, I hit curbs... The front bumper will be repainted (again) with the hood... Then if I scrape the bottom more it's getting taped off and black rubber/undercoating sprayed on![Winky](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_wink.gif)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust17.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust15.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust14.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust13.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust11.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust12.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust19.jpg)
Yes, I hit curbs... The front bumper will be repainted (again) with the hood... Then if I scrape the bottom more it's getting taped off and black rubber/undercoating sprayed on
![Winky](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_wink.gif)
![](http://i31.photobucket.com/albums/c362/markdelisle/Custom%20Exhaust/CustomExhaust18.jpg)
#3
10 Second Club
iTrader: (14)
Join Date: Dec 2005
Location: Central California
Posts: 1,392
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech10year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
that has to be one of the nicest damn exhaust i have ever seen. I love the way they used the v-clamps and left plenty of clearance, just in case the tranny needed to be removed, and how it all flows evenly to the y merge.
anyways, looks badass dude!!
anyways, looks badass dude!!
#5
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by RooRnZ28
that has to be one of the nicest damn exhaust i have ever seen. I love the way they used the v-clamps and left plenty of clearance, just in case the tranny needed to be removed, and how it all flows evenly to the y merge.
anyways, looks badass dude!!
anyways, looks badass dude!!
They did do great work on the y-pipe though
![The Judge](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_judge.gif)
Trending Topics
#10
Registered User
iTrader: (1)
Join Date: May 2007
Location: Van Nuys
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
hahaha i saw you today. thats my ehaust shop Jose @ Bodywerks!! hes awesome does great work. i was in that toyota minivan (work car i was test driving) i let you pull out of the driveway in front of me. it sounded really nice. you should come out 2morrow night to flames in northridge and meet up with my car club. (check out the link under my sig)
#13
10 Second Club
iTrader: (53)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by QWIK_LT1
hahaha i saw you today. thats my ehaust shop Jose @ Bodywerks!! hes awesome does great work. i was in that toyota minivan (work car i was test driving) i let you pull out of the driveway in front of me. it sounded really nice. you should come out 2morrow night to flames in northridge and meet up with my car club. (check out the link under my sig)
![Bang Head](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_banghead.gif)
#14
8 Second Club
iTrader: (11)
Join Date: Feb 2002
Location: (760) Phelan Ca.
Posts: 757
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by geovett
what exhaust shop and who did u see? nine finger? did strictly perform. do the exhaust or your shop (jose)? and where is strictly perf..? ![Bang Head](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_banghead.gif)
![Bang Head](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_banghead.gif)
![Chug! Chug! Chug!](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_chug.gif)
#17
8 Second Club
iTrader: (11)
Join Date: Feb 2002
Location: (760) Phelan Ca.
Posts: 757
Likes: 0
Received 0 Likes
on
0 Posts
![](https://ls1tech.com/forums/images/ranks/ls1tech20year.png)
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by geovett
hey i'am up again where is that shop??? senor JOSE WHERE R U?
![Try Search](https://ls1tech.com/forums/images/smilies/trysearch.gif)
Found their info
Bodywerks Mufflers
7750 Sepulveda Blvd Ste 8
Van Nuys, CA 91405
(818) 786-2337
Last edited by Nine Finger 02 Z28; 06-15-2007 at 01:56 AM.
#20
![Default](https://ls1tech.com/forums/images/icons/icon1.gif)
Originally Posted by QWIK_LT1
hahaha i saw you today. thats my ehaust shop Jose @ Bodywerks!! hes awesome does great work. i was in that toyota minivan (work car i was test driving) i let you pull out of the driveway in front of me. it sounded really nice. you should come out 2morrow night to flames in northridge and meet up with my car club. (check out the link under my sig)
![Icon Lol](https://ls1tech.com/forums/images/smilies2/icon_lol.gif)
![Happy](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_stretch.gif)
![The Jester](https://ls1tech.com/forums/images/smilies/LS1Tech/gr_jest.gif)
Did you see the Medium Blue Metallic Trans-Am when I turned right and you went left? I snapped some pics:
![](http://i31.photobucket.com/albums/c362/markdelisle/MBMTrans-Am.jpg)
![](http://i31.photobucket.com/albums/c362/markdelisle/MBMTrans-Am1.jpg)
Nice looking rare car and it was clean so I would assume the owner knows he has something cool on his hands... Do you know the car?
I'll try to make it out there tommorrow night...