. Take in mind my only mistake is spending most of my money on my car with a fucked up economy.
turbo kits?
But you will still need a bracket/pullie and a front mont intercooler if you desire. It will begin to add up, you can pick up a used p1sc procharger kit for high 2ks and it will be emissions legal since it has a carb sticker.
lol you should be proud, you hacked up your car to beat a stock camaro. pat yourself on the back, not many could have done it.
https://ls1tech.com/forums/showpost....21&postcount=1
carbonfiberbird the cheapest way to turbo is doing a truck manifold kit, But like ryne said it won't be emissions legal. depending on your hp goal you might have to do a fuel pump and injectors and don't forget a speed density tune. I got deep with my build and did my entire drivetrain and complete fuel system. I doubt my boosted ls1 will last but my intentions are to push it till it blows just like camarojunky.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Coachbuilt N2A Anteros Is an LS2-Powered C6 Corvette In Italian Clothes
Verdad Gallardo
its not hate, i just wanted to point a friend in the right direction. from the outside looking in it looks like a mistake. on the other hand i hope i have to eat my words when you get that car dialed in and put up some nice numbers.
Nothing about Forced Induction is cheap.
Even with a 6.0 truck manifold kit A quality turbo, wastegate, and Bov and flanges will be close to 2k, alumanized pipe 300-600, stainless, 600-1000. then you have to buy the intercooler and all the associated aluminum pipe that will have to get welded. plus you lose your AC. If you run aluminized pipe then you have to wrap it to keep it from rusting and to help keep the heat in, for stainless it should be tig'd and coated, but a wrap will be ok.
If you run the turbo in the rear your aluminum cost goes up as well as having to buy quality a scavenge pump to circulate the oil for the turbo.
so now you have 3-4k into your DIY setup and you have to buy all the supporting pieces, Converter, clutch, trans, injectors, new rear, forged shortblock, boost guage, boost controler etc.
So take your original 4k budget and double it, now you are close to what it may cost to get the car running.
Even with a 6.0 truck manifold kit A quality turbo, wastegate, and Bov and flanges will be close to 2k, alumanized pipe 300-600, stainless, 600-1000. then you have to buy the intercooler and all the associated aluminum pipe that will have to get welded. plus you lose your AC. If you run aluminized pipe then you have to wrap it to keep it from rusting and to help keep the heat in, for stainless it should be tig'd and coated, but a wrap will be ok.
If you run the turbo in the rear your aluminum cost goes up as well as having to buy quality a scavenge pump to circulate the oil for the turbo.
so now you have 3-4k into your DIY setup and you have to buy all the supporting pieces, Converter, clutch, trans, injectors, new rear, forged shortblock, boost guage, boost controler etc.
So take your original 4k budget and double it, now you are close to what it may cost to get the car running.
Going the turbo route can be expensive, but it would be cool if you get it right, and it runs hard in the end.
Your car would be badass with a head/cam swap. Naturally aspirated (maybe some nitrous
) F T W!!! 
thats probably what I am going to end up doing, - the no2, I am not a fas of nitrous. I was thinking for now just getting a ms3 cam and some LTs
like juiced said forced induction is not cheap https://ls1tech.com/forums/forced-induction/567592-real-price-forced-induction.html