Holeshots!!!
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
Holeshots!!! finally finally got them on...what do joo guise think?
15x3.5's up front w/ 26x7.5 MT sportsman's
15x10.5 in the rear with 325/50/15 nitto 555R's
next tires will be 275 MT ET street radials the 325 nitto's just run so much narrower then MT's I'm running a tiny spacer in the rear as I didn't have enough time to hammer the **** out of the fender wells, nor roll the lips.
car is getting tuned either tom or wed by Jeremy Formato one of if not the best LSX tuners in the country. 42lb injectors being installed as well, getting ready for the giggle gas
Chad
15x3.5's up front w/ 26x7.5 MT sportsman's
15x10.5 in the rear with 325/50/15 nitto 555R's
next tires will be 275 MT ET street radials the 325 nitto's just run so much narrower then MT's I'm running a tiny spacer in the rear as I didn't have enough time to hammer the **** out of the fender wells, nor roll the lips.
car is getting tuned either tom or wed by Jeremy Formato one of if not the best LSX tuners in the country. 42lb injectors being installed as well, getting ready for the giggle gas
Chad
I think they are hidious, absolutely awfull................................ now take them off and send them to me
LOL na they look good!!!! how much did they cost? Any clearence problems with brakes etc?
LOL na they look good!!!! how much did they cost? Any clearence problems with brakes etc? Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
and clearance...just like most of them it required grinding of the front and rears, the fronts aren't so bad, the rears on the other hand...just keep grinding was my moto, and you must grind the rear fins as well as the fronts. the rears will fit with no spacers but I'm running a small one now as I didn't have the time (or tools) to roll the fenders, and massage the fender wells.
Chad
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
Trending Topics
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
any way you keep it clean w/o the cap?
Chad
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
and they were about $500 for both fronts, I got the rears used from a buddy.
Chad
Thread Starter
12 Second Club
iTrader: (17)
Joined: Dec 2004
Posts: 1,449
Likes: 0
From: Cooper City, FL
soon as I get back home, give her a bath, alignment, lower the front and rear 0.5" and get rid of the spacer I'll post up new and better pictures, this was a 2 second take a picture with dad's point and shoot lol.
Chad