Runs better in open loop?
#1
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: Jul 2005
Location: Round Rock, Texas
Posts: 723
Likes: 0
Received 0 Likes
on
0 Posts
Runs better in open loop?
I have a 1989 firebird with a LQ9 swap, with a cam, exhaust, and stall. The car seems to run well in open loop, without the O2 sensors. However as soon as it goes into closed loop, it seems like it isn't as easy to rev the motor, it also seems to bog on decel.
I did have 2 vacuum leaks (unplugged vacuum ports on the manifold), apparently the guy who installed the motor didn't plug those. There was also a large leak around the drivers side collector that i recently fixed.
Is it possible that my tune is now off and the car actually runs more efficient in open loop? Is there a way I could keep it in open loop to test the theory? I just don't understand why it feels so much more "snappy" in open loop, and turns into a slug in closed loop.
No codes are shown, Both O2 sensors are new, no more exhaust leaks, good gaskets, etc.
I did have 2 vacuum leaks (unplugged vacuum ports on the manifold), apparently the guy who installed the motor didn't plug those. There was also a large leak around the drivers side collector that i recently fixed.
Is it possible that my tune is now off and the car actually runs more efficient in open loop? Is there a way I could keep it in open loop to test the theory? I just don't understand why it feels so much more "snappy" in open loop, and turns into a slug in closed loop.
No codes are shown, Both O2 sensors are new, no more exhaust leaks, good gaskets, etc.
#3
Moderator
iTrader: (11)
Join Date: Mar 2002
Location: East Central Florida
Posts: 12,604
Likes: 0
Received 6 Likes
on
6 Posts
This could be sensor temperature related if you're
running long tubes (esp. uncoated), leading to a
false trimming. So could the exhaust air leaks, but
this should "settle in" over time.
If it runs well in open loop, at least your base tune
is not-insane. That's the good news. Trick is to get
closed loop to go along.
Got scan?
running long tubes (esp. uncoated), leading to a
false trimming. So could the exhaust air leaks, but
this should "settle in" over time.
If it runs well in open loop, at least your base tune
is not-insane. That's the good news. Trick is to get
closed loop to go along.
Got scan?
#4
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: Jul 2005
Location: Round Rock, Texas
Posts: 723
Likes: 0
Received 0 Likes
on
0 Posts
I wish i had scan/tune software. Best I can do is make educated guesses at the moment and make sure everything works ok (scary I know). It runs awesome at WOT, and will spin the tires from a 60mph roll, but acts like a dog in most other situations. Drives me crazy!
#6
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: Jul 2005
Location: Round Rock, Texas
Posts: 723
Likes: 0
Received 0 Likes
on
0 Posts
What is the cheapest option to get tuning myself? I really don't want this motor going down hill, if it pops, the car is getting sold off for parts, and it's my high school car. Should have kept the TPI honestly LOL
HPtuners and LS1edit seem to be about the same price, but are all programs really THAT expensive? It's either buy the program myself, or pay some one the same amount to tune it for me, but I don't get to keep the software....
HPtuners and LS1edit seem to be about the same price, but are all programs really THAT expensive? It's either buy the program myself, or pay some one the same amount to tune it for me, but I don't get to keep the software....
#7
TECH Enthusiast
Thread Starter
iTrader: (7)
Join Date: Jul 2005
Location: Round Rock, Texas
Posts: 723
Likes: 0
Received 0 Likes
on
0 Posts
Well since it double posted, Is there anyway I could try to keep the car in open loop? Also I remember the tuner saying they couldn't get the KR down, I believe it was because of false knock. So max timing is only ever 20*, which seems very low, considering some seem to run mid 30-40s...
Could I unplug the Knock sensor and see what it does?
Could I unplug the Knock sensor and see what it does?
Trending Topics
#8
TECH Fanatic
iTrader: (9)
You sound like the kind of person that would be able to learn to tune with HP tuners or EFI Live pretty quickly. I personaly use HP Tuners and therefore I sugest it over others because I know it.
If you bought HP or EFI you can correct all your issues, learn how to tune, and be able to tune the car for future mods. Either realy is a great investment if you plan to play with your car. Both are more then worth the asking price. Thats were you should go before you start unpluging things.
If you bought HP or EFI you can correct all your issues, learn how to tune, and be able to tune the car for future mods. Either realy is a great investment if you plan to play with your car. Both are more then worth the asking price. Thats were you should go before you start unpluging things.
#9
TECH Fanatic
iTrader: (3)
Join Date: Feb 2009
Location: Highland, MI
Posts: 1,366
Likes: 0
Received 0 Likes
on
0 Posts
You sound like the kind of person that would be able to learn to tune with HP tuners or EFI Live pretty quickly. I personaly use HP Tuners and therefore I sugest it over others because I know it.
If you bought HP or EFI you can correct all your issues, learn how to tune, and be able to tune the car for future mods. Either realy is a great investment if you plan to play with your car. Both are more then worth the asking price. Thats were you should go before you start unpluging things.
If you bought HP or EFI you can correct all your issues, learn how to tune, and be able to tune the car for future mods. Either realy is a great investment if you plan to play with your car. Both are more then worth the asking price. Thats were you should go before you start unpluging things.
you shouldn't unplug you knock sensors, no. I had a case of false KR on my car and I tuned the sensors. I would say buy the hptuners software also, it will take time to become a good tuner but its worth it.
#10
10 Second Club
iTrader: (3)
Join Date: Feb 2009
Location: tn.
Posts: 210
Likes: 0
Received 0 Likes
on
0 Posts
I might be wrong but i was thinking it stays in open loop until the o2 sensors reach operating temp. If that's the case it would stay in open loop if you unplug o2 sensors, but that wouldn't be the way too fix the problem.
#14
TECH Fanatic
iTrader: (3)
Join Date: Feb 2009
Location: Highland, MI
Posts: 1,366
Likes: 0
Received 0 Likes
on
0 Posts
Just to clarify I wasn't agreeing that closed loop is dependent on O2 temperature, I was agreeing that disconnecting them will force the system into open loop.
and yes, closed loop is based on coolant temperature.
and yes, closed loop is based on coolant temperature.
#15
TECH Fanatic
iTrader: (9)
part of the reason the engine runs better in Open loop is because while the coolant temp is still lower and the pcm is operating in OL the PCM is targetting a richer AFR then it does in Closed loop. Once it goes to CL it will be targetting Stoich (14.68). Depending on the size of the cam that might be too lean to make the engine idle right. It will make the engine choppier due to it being so much leaner. I personal have been running my setup in Open Loop Speed Density 3 bar and I target and tune my Open loop tables with a wide band to 13:1 AFR. At that richer setting the car sounds almost stock, very little lope. Once I let it go to Closed loop and the WB are reporting 14.6 as comanded it idles very ruff and the drivability goes to $h!t as compaired to Open Loop.
What i am saying is there comes a point depending on setup that closed loop operation becomes a hassle.
Pros to Open loop operation at all times is you can run wilder cams and mods and the engine will operate as desired.
Con to Open Loop operation; fuel economy is sacrificed. But I am not a green guy and could care less about economy.
I think you can tune to be in open loop more at slow speed and to go into closed loop once you get up to cruise speeds. I personaly have yet to get to that point. Maybe someone here can shed som light on this.
What i am saying is there comes a point depending on setup that closed loop operation becomes a hassle.
Pros to Open loop operation at all times is you can run wilder cams and mods and the engine will operate as desired.
Con to Open Loop operation; fuel economy is sacrificed. But I am not a green guy and could care less about economy.
I think you can tune to be in open loop more at slow speed and to go into closed loop once you get up to cruise speeds. I personaly have yet to get to that point. Maybe someone here can shed som light on this.
#16
TECH Fanatic
iTrader: (3)
Join Date: Feb 2009
Location: Highland, MI
Posts: 1,366
Likes: 0
Received 0 Likes
on
0 Posts
part of the reason the engine runs better in Open loop is because while the coolant temp is still lower and the pcm is operating in OL the PCM is targetting a richer AFR then it does in Closed loop. Once it goes to CL it will be targetting Stoich (14.68). Depending on the size of the cam that might be too lean to make the engine idle right. It will make the engine choppier due to it being so much leaner. I personal have been running my setup in Open Loop Speed Density 3 bar and I target and tune my Open loop tables with a wide band to 13:1 AFR. At that richer setting the car sounds almost stock, very little lope. Once I let it go to Closed loop and the WB are reporting 14.6 as comanded it idles very ruff and the drivability goes to $h!t as compaired to Open Loop.
What i am saying is there comes a point depending on setup that closed loop operation becomes a hassle.
Pros to Open loop operation at all times is you can run wilder cams and mods and the engine will operate as desired.
Con to Open Loop operation; fuel economy is sacrificed. But I am not a green guy and could care less about economy.
I think you can tune to be in open loop more at slow speed and to go into closed loop once you get up to cruise speeds. I personaly have yet to get to that point. Maybe someone here can shed som light on this.
What i am saying is there comes a point depending on setup that closed loop operation becomes a hassle.
Pros to Open loop operation at all times is you can run wilder cams and mods and the engine will operate as desired.
Con to Open Loop operation; fuel economy is sacrificed. But I am not a green guy and could care less about economy.
I think you can tune to be in open loop more at slow speed and to go into closed loop once you get up to cruise speeds. I personaly have yet to get to that point. Maybe someone here can shed som light on this.
#17
TECH Fanatic
iTrader: (9)
I need to get some pointers from you and how to make the tune "hybrid". I prefer the way my car idles and drives around town under 40 mph in OL but I would like to have it go into CL when I get out on the hyway, were it runs just fine at the leaner 14.6 comanded AFR.
Any direction on doing this would be very helpful.
Any direction on doing this would be very helpful.
#19
TECH Enthusiast
iTrader: (1)
Join Date: Dec 2005
Location: Denver International Airport, Colorado USA
Posts: 549
Likes: 0
Received 0 Likes
on
0 Posts
I think 'Texas' was on to something.
Granted my cam is not wild, but I chose to stay closed-loop. I did all the usual tuning of the VE Table and MAF. For what it is worth I simply changed the O2 Switch-points to 550mv instead of the usually lower stock values.
Took almost all the air out of the Throttle Cracker below 2200 Rpm's. Whether changing the Narrow-band O2's 'really' work.while I can not specifically prove it..at least my wideband reads what I command and the Trims keep highway AFR at ~14.7.
If you can get closed-loop to work..it is really not a bad thing. It may just get to challenging as you start getting into the more wild cam profiles and larger injectors.
Good luck.
..WeathermanShawn..
Granted my cam is not wild, but I chose to stay closed-loop. I did all the usual tuning of the VE Table and MAF. For what it is worth I simply changed the O2 Switch-points to 550mv instead of the usually lower stock values.
Took almost all the air out of the Throttle Cracker below 2200 Rpm's. Whether changing the Narrow-band O2's 'really' work.while I can not specifically prove it..at least my wideband reads what I command and the Trims keep highway AFR at ~14.7.
If you can get closed-loop to work..it is really not a bad thing. It may just get to challenging as you start getting into the more wild cam profiles and larger injectors.
Good luck.
..WeathermanShawn..